Skip to main content

PTCL/Tenda W150D and Micronet SP3367NL (Broadcom) Telnet Commands Part 1/2

With Telnet access, more options become available that are not accessible via the web interface! Since the router uses the Broadcom chipset, we can apply almost all the same tweaks as documented for other Broadcom based routers:

Here is the list of commands (Password is the one set by you):

 BCM96328 Broadband Router  
 Login: admin  
 Password:   
 > ?  
 ?  
 help  
 logout  
 exit  
 quit  
 reboot  
 adsl  
 xdslctl  
 xtm  
 brctl  
 cat  
 loglevel  
 logdest  
 virtualserver  
 ddns  
 syslog  
 echo  
 ifconfig  
 ping  
 ps  
 pwd  
 sntp  
 sysinfo  
 tftp  
 wlctl  
 arp  
 defaultgateway  
 dhcpserver  
 dns  
 lan  
 lanhosts  
 passwd  
 ppp  
 restoredefault  
 route  
 save  
 swversion  
 cfgupdate  
 swupdate  
 exitOnIdle  
 wan  

There is also Shell access:
 > sh  
 BusyBox v1.00 (2012.05.30-12:11+0000) Built-in shell (msh)  
 Enter 'help' for a list of built-in commands.  

With regards to dsl modem, the commands "adsl" and "xdslctl" are important though anyone of these can be used!

  > xdslctl  
 Usage: xdslctl start [--up] [--mod <a|d|l|t|2|p|e|m|M3|M5>] [--lpair <(i)nner|(o)uter>]  
       [--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>]  
       [--sra <on|off>] [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt <0xBitMap-UsDs>]  
       [--Ginp <0xBitMap-UsDs>] [--TpsTc <0xBitMap-AvPvAaPa>] [--monitorTone <on|off>]  
       [--forceJ43 <on|off>] [--toggleJ43B43 <on|off>]  
     xdslctl stop  
     xdslctl connection [--up] [--down] [--loopback] [--reverb]  
       [--medley] [--noretrain] [--L3] [--diagmode] [--L0]  
       [--tones] [--normal] [--freezeReverb] [--freezeMedley]  
     xdslctl configure [--mod <a|d|l|t|2|p|e|m|M3|M5>] [--lpair <(i)nner|(o)uter>]  
       [--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>]  
       [--sra <on|off>] [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt <0xBitMap-UsDs>]  
       [--Ginp <0xBitMap-UsDs>] [--TpsTc <0xBitMap-AvPvAaPa>] [--monitorTone <on|off>]  
       [--forceJ43 <on|off>] [--toggleJ43B43 <on|off>]  
     xdslctl bert [--start <#seconds>] [--stop] [--show]  
     xdslctl afelb [--time <sec>] [--tones] [--signal <1/2/8>]   
     xdslctl qlnmntr [--time <sec>] [--freq <msec>]  
     xdslctl inm [--start <BB_THRESH 10*dB> <INMIATO> <INMIATS>] [--stop] [--show]  
     xdslctl snrclamp [--shape <shapeId>] [--bpshape [bpIndex-bpLevel,]]  
     xdslctl nlnm [--show ] [--setThld <Thld_Num_Tones>]  
     xdslctl diag [--logstart <nBytes>] [--logpause] [--logstop] [--loguntilbufferfull <nBytes>]  
       [--loguntilretrain <nBytes>]  
     xdslctl info [--state] [--show] [--stats] [--SNR] [--QLN] [--Hlog] [--Hlin] [--HlinS] [--Bits]  
       [--linediag] [--reset] [--vendor] [--cfg]  
     xdslctl profile [--show] [--save] [--restore]  
     xdslctl --version  
     xdslctl --help  

continues ...


In the next part, we'll take a look at some SNR tweaking and Stability options for the modem part and perhaps we'll look at the wireless section "wlctl" as well!
  > wlctl  
 Usage: wlctl [-a|i <adapter>] [-h] [-d|u|x] <command> [arguments]  
   
  -h    this message and command descriptions  
  -h [cmd] command description for cmd  
  -a, -i  adapter name or number  
  -d    output format signed integer  
  -u    output format unsigned integer  
  -x    output format hexdecimal  
   
 ver   get version information  
   
 cmds  generate a short list of available commands  
   
 up   reinitialize and mark adapter up (operational)  
   
 down  reset and mark adapter down (disabled)  
   
 out   mark adapter down but do not reset hardware(disabled)  
     On dualband cards, cards must be bandlocked before use.  
   
 clk   set board clock state. return error for set_clk attempt if the driver is not down  
     0: clock off  
     1: clock on  
   
 restart Restart driver. Driver must already be down.  
   
 reboot Reboot platform  
   
 radio  Set the radio on or off.  
     "on" or "off"  
   
 dump  Give suboption "list" to list various suboptions  
   
 srclear Clears first 'len' bytes of the srom, len in decimal or hex  
     Usage: srclear <len>  
   
 srdump print contents of SPROM to stdout  
   
 srwrite Write the srom: srwrite byteoffset value  
   
 srcrc  Get the CRC for input binary file  
   
 ciswrite  
     Write specified <file> to the SDIO CIS source (either SROM or OTP)  
   
 cisupdate  
     Write a hex byte stream to specified byte offset to the CIS source (either SROM or OTP)  
 --preview option allows you to review the update without committing it  
     <byte offset> <hex byte stream> [--preview]  
   
 cisdump Display the content of the SDIO CIS source  
     -b <file> -- also write raw bytes to <file>  
     <len> -- optional count of bytes to display (must be even)  
   
 cis_source  
     Display which source is used for the SDIO CIS  
   
 cisconvert  
     Print CIS tuple for given name=value pair  
   
 rdvar  Read a named variable to the srom  
   
 wrvar  Write a named variable to the srom  
   
 nvram_source  
     Display which source is used for nvram  
   
 nvram_dump  
     print nvram variables to stdout  
   
 nvset  set an nvram variable  
     name=value (no spaces around '=')  
   
 nvget  get the value of an nvram variable  
   
 nvram_get  
     get the value of an nvram variable  
   
 revinfo get hardware revision information  
   
 customvar1  
     print the value of customvar1 in hex format  
   
 msglevel  
     set driver console debugging message bitvector  
     type 'wl msglevel ?' for values  
   
 phymsglevel  
     set phy debugging message bitvector  
     type 'wl phymsglevel ?' for values  
   
 PM   set driver power management mode:  
     0: CAM (constantly awake)  
     1: PS (power-save)  
     2: FAST PS mode  
   
 wake  set driver power-save mode sleep state:  
     0: core-managed  
     1: awake  
   
 promisc set promiscuous mode ethernet address reception  
     0 - disable  
     1 - enable  
   
 monitor set monitor mode  
     0 - disable  
     1 - enable active monitor mode (interface still operates)  
   
 frag  Deprecated. Use fragthresh.  
   
 rts   Deprecated. Use rtsthresh.  
   
 cwmin  Set the cwmin. (integer [1, 255])  
   
 cwmax  Set the cwmax. (integer [256, 2047])  
   
 srl   Set the short retry limit. (integer [1, 255])  
   
 lrl   Set the long retry limit. (integer [1, 255])  
   
 rate  force a fixed rate:  
     valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)  
     valid values for 802.11b are (1, 2, 5.5, 11)  
     valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)  
     -1 (default) means automatically determine the best rate  
   
 mrate  force a fixed multicast rate:  
     valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)  
     valid values for 802.11b are (1, 2, 5.5, 11)  
     valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)  
     -1 (default) means automatically determine the best rate  
   
 a_rate force a fixed rate for the A PHY:  
     valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)  
     -1 (default) means automatically determine the best rate  
   
 a_mrate force a fixed multicast rate for the A PHY:  
     valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)  
     -1 (default) means automatically determine the best rate  
   
 bg_rate force a fixed rate for the B/G PHY:  
     valid values for 802.11b are (1, 2, 5.5, 11)  
     valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)  
     -1 (default) means automatically determine the best rate  
   
 bg_mrate  
     force a fixed multicast rate for the B/G PHY:  
     valid values for 802.11b are (1, 2, 5.5, 11)  
     valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)  
     -1 (default) means automatically determine the best rate  
   
 infra  Set Infrastructure mode: 0 (IBSS) or 1 (Infra BSS)  
   
 ap   Set AP mode: 0 (STA) or 1 (AP)  
   
 bssid  Get the BSSID value, error if STA and not associated  
   
 bssmax get number of BSSes   
   
 channel Set the channel:  
     valid channels for 802.11b/g (2.4GHz band) are 1 through 14  
     valid channels for 802.11a (5 GHz band) are:  
         36, 40, 44, 48, 52, 56, 60, 64,  
         100, 104, 108, 112, 116,120, 124, 128, 132, 136, 140,  
         149, 153, 157, 161,  
         184, 188, 192, 196, 200, 204, 208, 212, 216  
   
 cur_mcsset  
     Get the current mcs set  
   
 chanspecs  
     Get all the valid chanspecs (default: all within current locale):  
     -b band (5(a) or 2(b/g))  
     -w bandwidth, 10,20 or 40  
     [-c country_abbrev]  
   
 chanspec  
     Set <channel>[a,b][n][u,l]  
     channel number (0-224)  
     band a=5G, b=2G, default to 2G if channel <= 14  
     bandwidth, n=10, none for 20 & 40  
     ctl sideband, l=lower, u=upper  
 OR Set channel with legacy format:  
     -c channel number (0-224)  
     -b band (5(a) or 2(b/g))  
     -w bandwidth, 10,20 or 40  
     -s ctl sideband, -1=lower, 0=none, 1=upper  
   
 dfs_channel_forced  
     Set <channel>[a,b][n][u,l]  
     channel number (0-224)  
     band a=5G, b=2G, default to 2G if channel <= 14  
     bandwidth, n=10, non for 20 & 40  
     ctl sideband, l=lower, u=upper  
   
 tssi  Get the tssi value from radio  
   
 txpwr  Set tx power in milliwatts. Range [1, 84].  
   
 txpwr1 Set tx power in in various units. Choose one of (default: dbm):   
     -d dbm units  
     -q quarter dbm units  
     -m milliwatt units  
 Can be combined with:  
     -o turn on override to disable regulatory and other limitations  
 Use wl txpwr -1 to restore defaults  
   
 txpathpwr  
     Turn the tx path power on or off on 2050 radios  
   
 txpwrlimit  
     Return current tx power limit  
   
 powerindex  
     Set the transmit power for A band(0-63).  
     -1 - default value  
   
 atten  Set the transmit attenuation for B band. Args: bb radio txctl1.  
     auto to revert to automatic control  
     manual to supspend automatic control  
   
 phyreg Get/Set a phy register:  
     offset [ value ] [ band ]  
   
 radioreg  
     Get/Set a radio register:  
     offset [ value ] [ band/core ]  
 HTPHY:  
     Get a radio register: wl radioreg [ offset ] [ cr0/cr1/cr2 ]  
     Set a radio register: wl radioreg [ offset ] [ value ] [ cr0/cr1/cr2/all ]  
   
   
 ucflags Get/Set ucode flags 1, 2, 3(16 bits each)  
     offset [ value ] [ band ]  
   
 shmem  Get/Set a shared memory location:  
     offset [ value ] [band ]  
   
 macreg Get/Set any mac registers(include IHR and SB):  
     macreg offset size[2,4] [ value ] [ band ]  
   
 ucantdiv  
     Enable/disable ucode antenna diversity (1/0 or on/off)  
   
 gpioout Set any GPIO pins to any value. Use with caution as GPIOs would be assigned to chipcommon  
     Usage: gpiomask gpioval  
   
 devpath print device path  
   
 pcieserdesreg  
     g/set SERDES registers: dev offset [val]  
   
 ampdu_activate_test  
     actiate  
   
 ampdu_tid  
     enable/disable per-tid ampdu; usage: wl ampdu_tid <tid> [0/1]  
   
 ampdu_retry_limit_tid  
     Set per-tid ampdu retry limit; usage: wl ampdu_retry_limit_tid <tid> [0~31]  
   
 ampdu_rr_retry_limit_tid  
     Set per-tid ampdu regular rate retry limit; usage: wl ampdu_rr_retry_limit_tid <tid> [0~31]  
   
 ampdu_send_addba  
     send addba to specified ea-tid; usage: wl ampdu_send_addba <tid> <ea>  
   
 ampdu_send_delba  
     send delba to specified ea-tid; usage: wl ampdu_send_delba <tid> <ea>  
   
 ampdu_clear_dump  
     clear ampdu counters  
   
 dpt_deny  
     adds/removes ea to dpt deny list  
     usage: wl dpt_deny <add,remove> <ea>  
   
 dpt_endpoint  
     creates/updates/deletes dpt endpoint for ea  
     usage: wl dpt_endpoint <create, update, delete> <ea>  
   
 dpt_pmk sets DPT pre-shared key  
   
 dpt_fname  
     sets/gets DPT friendly name  
   
 dpt_list  
     gets status of all dpt peers  
   
 actframe  
     Send a Vendor specific Action frame to a channel  
     usage: wl actframe <Dest Mac Addr> <data> channel dwell-time <BSSID>  
   
 antdiv Set antenna diversity for rx  
     0 - force use of antenna 0  
     1 - force use of antenna 1  
     3 - automatic selection of antenna diversity  
   
 txant  Set the transmit antenna  
     0 - force use of antenna 0  
     1 - force use of antenna 1  
     3 - use the RX antenna selection that was in force during  
       the most recently received good PLCP header  
   
 plcphdr Set the plcp header.  
     "long" or "auto" or "debug"  
   
 phytype Get phy type  
   
 rateparam  
     set driver rate selection tunables  
     arg 1: tunable id  
     arg 2: tunable value  
   
 wepstatus  
     Set or Get WEP status  
     wepstatus [on|off]  
   
 primary_key  
     Set or get index of primary key  
   
 addwep Set an encryption key. The key must be 5, 13 or 16 bytes long, or  
     10, 26, 32, or 64 hex digits long. The encryption algorithm is  
     automatically selected based on the key size. keytype is accepted  
     only when key length is 16 bytes/32 hex digits and specifies  
     whether AES-OCB or AES-CCM encryption is used. Default is ccm.  
     WAPI is selected if key len is 32 and arguments contain wapi.  
     addwep <keyindex> <keydata> [ocb | ccm | wapi] [notx] [xx:xx:xx:xx:xx:xx]  
   
 rmwep  Remove the encryption key at the specified key index.  
   
 keys  Prints a list of the current WEP keys  
   
 tsc   Print Tx Sequence Couter for key at specified key index.  
   
 wsec_test  
     Generate wsec errors  
     wsec_test <test_type> <keyindex|xx:xx:xx:xx:xx:xx>  
     type 'wl wsec_test ?' for test_types  
   
 tkip_countermeasures  
     Enable or disable TKIP countermeasures (TKIP-enabled AP only)  
     0 - disable  
     1 - enable  
   
 wsec_restrict  
     Drop unencrypted packets if WSEC is enabled  
     0 - disable  
     1 - enable  
   
 eap   restrict traffic to 802.1X packets until 802.1X authorization succeeds  
     0 - disable  
     1 - enable  
   
 cur_etheraddr  
     Get/set the current hw address  
   
 perm_etheraddr  
     Get the permanent address from NVRAM  
   
 authorize  
     restrict traffic to 802.1X packets until 802.1X authorization succeeds  
   
 deauthorize  
     do not restrict traffic to 802.1X packets until 802.1X authorization succeeds  
   
 deauthenticate  
     deauthenticate a STA from the AP with optional reason code (AP ONLY)  
   
 wsec  wireless security bit vector  
     1 - WEP enabled  
     2 - TKIP enabled  
     4 - AES enabled  
     8 - WSEC in software  
     0x80 - FIPS enabled  
     0x100 - WAPI enabled  
   
 auth  set/get 802.11 authentication type. 0 = OpenSystem, 1= SharedKey, 2=Open/Shared  
   
 wpa_auth  
     Bitvector of WPA authorization modes:  
     1    WPA-NONE  
     2    WPA-802.1X/WPA-Professional  
     4    WPA-PSK/WPA-Personal  
     64   WPA2-802.1X/WPA2-Professional  
     128   WPA2-PSK/WPA2-Personal  
     0    disable WPA  
   
 wpa_cap set/get 802.11i RSN capabilities  
   
 set_pmk Set passphrase for PMK in driver-resident supplicant.  
   
 scan  Initiate a scan.  
     Default to an active scan across all channels for any SSID.  
     Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).  
     Options:  
     -s S, --ssid=S     SSIDs to scan  
     -t ST, --scan_type=ST  [active|passive|prohibit] scan type  
     --bss_type=BT      [bss/infra|ibss/adhoc] bss type to scan  
     -b MAC, --bssid=MAC   particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx  
     -n N, --nprobes=N    number of probes per scanned channel  
     -a N, --active=N    dwell time per channel for active scanning  
     -p N, --passive=N    dwell time per channel for passive scanning  
     -h N, --home=N     dwell time for the home channel between channel scans  
     -c L, --channels=L   comma or space separated list of channels to scan  
   
 iscan_s Initiate an incremental scan.  
     Default to an active scan across all channels for any SSID.  
     Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).  
     Options:  
     -s S, --ssid=S     SSIDs to scan  
     -t ST, --scan_type=ST  [active|passive|prohibit] scan type  
     --bss_type=BT      [bss/infra|ibss/adhoc] bss type to scan  
     -b MAC, --bssid=MAC   particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx  
     -n N, --nprobes=N    number of probes per scanned channel  
     -a N, --active=N    dwell time per channel for active scanning  
     -p N, --passive=N    dwell time per channel for passive scanning  
     -h N, --home=N     dwell time for the home channel between channel scans  
     -c L, --channels=L   comma or space separated list of channels to scan  
   
 iscan_c Continue an incremental scan.  
     Default to an active scan across all channels for any SSID.  
     Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).  
     Options:  
     -s S, --ssid=S     SSIDs to scan  
     -t ST, --scan_type=ST  [active|passive|prohibit] scan type  
     --bss_type=BT      [bss/infra|ibss/adhoc] bss type to scan  
     -b MAC, --bssid=MAC   particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx  
     -n N, --nprobes=N    number of probes per scanned channel  
     -a N, --active=N    dwell time per channel for active scanning  
     -p N, --passive=N    dwell time per channel for passive scanning  
     -h N, --home=N     dwell time for the home channel between channel scans  
     -c L, --channels=L   comma or space separated list of channels to scan  
   
 scancache_clear  
     clear the scan cache  
   
 escan  Start an escan.  
     Default to an active scan across all channels for any SSID.  
     Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).  
     Options:  
     -s S, --ssid=S     SSIDs to scan  
     -t ST, --scan_type=ST  [active|passive|prohibit] scan type  
     --bss_type=BT      [bss/infra|ibss/adhoc] bss type to scan  
     -b MAC, --bssid=MAC   particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx  
     -n N, --nprobes=N    number of probes per scanned channel  
     -a N, --active=N    dwell time per channel for active scanning  
     -p N, --passive=N    dwell time per channel for passive scanning  
     -h N, --home=N     dwell time for the home channel between channel scans  
     -c L, --channels=L   comma or space separated list of channels to scan  
   
 escanabort  
     Abort an escan.  
     Default to an active scan across all channels for any SSID.  
     Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).  
     Options:  
     -s S, --ssid=S     SSIDs to scan  
     -t ST, --scan_type=ST  [active|passive|prohibit] scan type  
     --bss_type=BT      [bss/infra|ibss/adhoc] bss type to scan  
     -b MAC, --bssid=MAC   particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx  
     -n N, --nprobes=N    number of probes per scanned channel  
     -a N, --active=N    dwell time per channel for active scanning  
     -p N, --passive=N    dwell time per channel for passive scanning  
     -h N, --home=N     dwell time for the home channel between channel scans  
     -c L, --channels=L   comma or space separated list of channels to scan  
   
 passive Puts scan engine into passive mode  
   
 regulatory  
     Get/Set regulatory domain mode (802.11d). Driver must be down.  
   
 spect  Get/Set 802.11h Spectrum Management mode.  
     0 - Off  
     1 - Loose interpretation of 11h spec - may join non-11h APs  
     2 - Strict interpretation of 11h spec - may not join non-11h APs  
     3 - Disable 11h and enable 11d  
     4 - Loose interpretation of 11h+d spec - may join non-11h APs  
   
 scanabort  
     Abort a scan.  
   
 scanresults  
     Return results from last scan.  
   
 iscanresults  
     Return results from last iscan. Specify a buflen (max 8188)  
     to artificially limit the size of the results buffer.  
     iscanresults [buflen]  
   
 assoc  Print information about current network association.  
     (also known as "status")  
   
 status Print information about current network association.  
     (also known as "assoc")  
   
 disassoc  
     Disassociate from the current BSS/IBSS.  
   
 chanlist  
     Deprecated. Use channels.  
   
 channels  
     Return valid channels for the current settings.  
   
 channels_in_country  
     Return valid channels for the country specified.  
     Arg 1 is the country abbreviation  
     Arg 2 is the band(a or b)  
   
 curpower  
     Return current tx power settings.  
     -q (quiet): estimated power only.  
   
 curppr Return current tx power per rate offset.  
   
   
 txinstpwr  
     Return tx power based on instant TSSI   
   
 scansuppress  
     Suppress all scans for testing.  
     0 - allow scans  
     1 - suppress scans  
   
 evm   Start an EVM test on the given channel, or stop EVM test.  
     Arg 1 is channel number 1-14, or "off" or 0 to stop the test.  
     Arg 2 is optional rate (1, 2, 5.5 or 11)  
   
 rateset Returns or sets the supported and basic rateset, (b) indicates basic  
     With no args, returns the rateset. Args are  
     rateset "default" | "all" | <arbitrary rateset> -m <arbitrary mcsset>  
         default - driver defaults  
         all - all rates are basic rates  
         arbitrary rateset - list of rates  
         arbitrary mcsset - list of mcs rates octets, each bit representing  
                 corresponding mcs  
     List of rates are in Mbps and each rate is optionally followed  
     by "(b)" or "b" for a Basic rate. Example: 1(b) 2b 5.5 11  
     At least one rate must be Basic for a legal rateset.  
   
 roam_trigger  
     Get or Set the roam trigger RSSI threshold:  
     Get: roam_trigger [a|b]  
     Set: roam_trigger <integer> [a|b|all]  
     integer -  0: default  
           1: optimize bandwidth  
           2: optimize distance  
       [-1, -99]: dBm trigger value  
   
 roam_delta  
     Set the roam candidate qualification delta. roam_delta [integer [, a/b]]  
   
 roam_scan_period  
     Set the roam candidate qualification delta. (integer)  
   
 suprates  
     Returns or sets the 11g override for the supported rateset  
     With no args, returns the rateset. Args are a list of rates,  
     or 0 or -1 to specify an empty rateset to clear the override.  
     List of rates are in Mbps, example: 1 2 5.5 11  
   
 scan_channel_time  
     Get/Set scan channel time  
   
 scan_unassoc_time  
     Get/Set unassociated scan channel dwell time  
   
 scan_home_time  
     Get/Set scan home channel dwell time  
   
 scan_passive_time  
     Get/Set passive scan channel dwell time  
   
 scan_nprobes  
     Get/Set scan parameter for number of probes to use per channel scanned  
   
 prb_resp_timeout  
     Get/Set probe response timeout  
   
 channel_qa  
     Get last channel quality measurment  
   
 channel_qa_start  
     Start a channel quality measurment  
   
 country Select Country Code for driver operational region  
     For simple country setting: wl country <country>  
     Where <country> is either a long name or country code from ISO 3166; for example "Germany" or "DE"  
   
     For a specific built-in country definition: wl country <built-in> [<advertised-country>]  
     Where <built-in> is a country country code followed by '/' and regulatory revision number.  
     For example, "US/3".  
     And where <advertised-country> is either a long name or country code from ISO 3166.  
     If <advertised-country> is omitted, it will be the same as the built-in country code.  
   
     Use 'wl country list [band(a or b)]' for the list of supported countries  
   
 country_ie_override  
     To set/get country ie  
   
 autocountry_default  
     Select Country Code for use with Auto Contry Discovery  
   
 join  Join a specified network SSID.  
     Usage: join <ssid> [key <0-3>:xxxxx] [imode bss|ibss] [amode open|shared|openshared|wpa|wpapsk|wpa2|wpa2psk|wpanone] [options]  
     Options:  
     -b MAC, --bssid=MAC   BSSID (xx:xx:xx:xx:xx:xx) to scan and join  
     -c CL, --chanspecs=CL  chanspecs (comma or space separated list)  
   
 ssid  Set or get a configuration's SSID.  
     wl ssid [-C num]|[--cfg=num] [<ssid>]  
     If the configuration index 'num' is not given, configuraion #0 is assumed and  
     setting will initiate an assoication attempt if in infrastructure mode,  
     or join/creation of an IBSS if in IBSS mode,  
     or creation of a BSS if in AP mode.  
   
 mac   Set or get the list of source MAC address matches.  
     wl mac xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]  
     To Clear the list: wl mac none  
   
 macmode Set the mode of the MAC list.  
     0 - Disable MAC address matching.  
     1 - Deny association to stations on the MAC list.  
     2 - Allow association to stations on the MAC list.  
   
 wds   Set or get the list of WDS member MAC addresses.  
     Set using a space separated list of MAC addresses.  
     wl wds xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]  
   
 lazywds Set or get "lazy" WDS mode (dynamically grant WDS membership to anyone).  
   
 noise  Get noise (moving average) right after tx in dBm  
   
 fqacurcy  
     Manufacturing test: set frequency accuracy mode.  
     freqacuracy syntax is: fqacurcy <channel>  
     Arg is channel number 1-14, or 0 to stop the test.  
   
 crsuprs Manufacturing test: set carrier suppression mode.  
     carriersuprs syntax is: crsuprs <channel>  
     Arg is channel number 1-14, or 0 to stop the test.  
   
 longtrain  
     Manufacturing test: set longtraining mode.  
     longtrain syntax is: longtrain <channel>  
     Arg is A band channel number or 0 to stop the test.  
   
 band  Returns or sets the current band  
     auto - auto switch between available bands (default)  
     a - force use of 802.11a band  
     b - force use of 802.11b band  
   
 bands  Return the list of available 802.11 bands  
   
 phylist Return the list of available phytypes  
   
 shortslot  
     Get current 11g Short Slot Timing mode. (0=long, 1=short)  
   
 shortslot_override  
     Get/Set 11g Short Slot Timing mode override. (-1=auto, 0=long, 1=short)  
   
 shortslot_restrict  
     Get/Set AP Restriction on associations for 11g Short Slot Timing capable STAs.  
     0 - Do not restrict association based on ShortSlot capability  
     1 - Restrict association to STAs with ShortSlot capability  
   
 ignore_bcns  
     AP only (G mode): Check for beacons without NONERP element(0=Examine beacons, 1=Ignore beacons)  
   
 pktcnt Get the summary of good and bad packets.  
   
 upgrade Upgrade the firmware on an embedded device  
   
 gmode  Set the 54g Mode (LegacyB|Auto||GOnly|BDeferred|Performance|LRS)  
   
 gmode_protection  
     Get G protection mode. (0=disabled, 1=enabled)  
   
 gmode_protection_control  
     Get/Set 11g protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)  
   
 gmode_protection_override  
     Get/Set 11g protection mode override. (-1=auto, 0=disable, 1=enable)  
   
 protection_control  
     Get/Set protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)  
   
 legacy_erp  
     Get/Set 11g legacy ERP inclusion (0=disable, 1=enable)  
   
 scb_timeout  
     AP only: inactivity timeout value for authenticated stas  
   
 assoclist  
     AP only: Get the list of associated MAC addresses.  
   
 isup  Get driver operational state (0=down, 1=up)  
   
 rssi  Get the current RSSI val, for an AP you must specify the mac addr of the STA  
   
 rssi_event  
     Set parameters associated with RSSI event notification  
     usage: wl rssi_event <rate_limit> <rssi_levels>  
     rate_limit: Number of events posted to application will be limited to 1 per this rate limit. Set to 0 to disable rate limit.  
     rssi_levels: Variable number of RSSI levels (maximum 8) in increasing order (e.g. -85 -70 -60). An event will be posted each time the RSSI of received beacons/packets crosses a level.  
   
 fasttimer  
     Deprecated. Use fast_timer.  
   
 slowtimer  
     Deprecated. Use slow_timer.  
   
 glacialtimer  
     Deprecated. Use glacial_timer.  
   
 radar  Enable/Disable radar  
   
 radarargs  
     Get/Set Radar parameters in   
     order as version, npulses, ncontig, min_pw, max_pw, thresh0,  
     thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp,  
     min_fm_lp, max_span_lp, min_deltat, max_deltat,  
     autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra,  
     npulses_stg2, npulses_stg3, percal_mask, quant,   
     min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask  
   
 radarargs40  
     Get/Set Radar parameters for 40Mhz channel in   
     order as version, npulses, ncontig, min_pw, max_pw, thresh0,  
     thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp,  
     min_fm_lp, max_span_lp, min_deltat, max_deltat,  
     autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra,  
     npulses_stg2, npulses_stg3, percal_mask, quant,   
     min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask  
   
 radarthrs  
     Set Radar threshold for both 20 & 40MHz BW:  
     order as thresh0_20_lo, thresh1_20_lo, thresh0_40_lo, thresh1_40_lo  
     thresh0_20_hi, thresh1_20_hi, thresh0_40_hi, thresh1_40_hi  
   
 dfs_status  
     Get dfs status  
   
 interference  
     Get/Set interference mitigation mode. Choices are:  
     0 = none  
     1 = non wlan  
     2 = wlan manual  
     3 = wlan automatic  
     4 = wlan automatic with noise reduction  
   
 interference_override  
     Get/Set interference mitigation override. Choices are:  
     0 = no interference mitigation  
     1 = non wlan  
     2 = wlan manual  
     3 = wlan automatic  
     4 = wlan automatic with noise reduction  
     -1 = remove override, override disabled  
   
 frameburst  
     Disable/Enable frameburst mode  
   
 pwr_percent  
     Get/Set power output percentage  
   
 toe   Enable/Disable tcpip offload feature  
   
 toe_ol Get/Set tcpip offload components  
   
 toe_stats  
     Display checksum offload statistics  
   
 toe_stats_clear  
     Clear checksum offload statistics  
   
 arpoe  Enable/Disable arp agent offload feature  
   
 arp_ol Get/Set arp offload components  
   
 arp_peerage  
     Get/Set age of the arp entry in minutes  
   
 arp_table_clear  
     Clear arp cache  
   
 arp_hostip  
     Add a host-ip address or display them  
   
 arp_hostip_clear  
     Clear all host-ip addresses  
   
 arp_stats  
     Display ARP offload statistics  
   
 arp_stats_clear  
     Clear ARP offload statistics  
   
 wet   Get/Set wireless ethernet bridging mode  
   
 bi   Get/Set the beacon period (bi=beacon interval)  
   
 dtim  Get/Set DTIM  
   
 wds_remote_mac  
     Get WDS link remote endpoint's MAC address  
   
 wds_wpa_role_old  
     Get WDS link local endpoint's WPA role (old)  
   
 wds_wpa_role  
     Get/Set WDS link local endpoint's WPA role  
   
 authe_sta_list  
     Get authenticated sta mac address list  
   
 autho_sta_list  
     Get authorized sta mac address list  
   
 measure_req  
     Send an 802.11h measurement request.  
     Usage: wl measure_req <type> <target MAC addr>  
     Measurement types are: TPC, Basic, CCA, RPI  
     Target MAC addr format is xx:xx:xx:xx:xx:xx  
   
 quiet  Send an 802.11h quiet command.  
     Usage: wl quiet <TBTTs until start>, <duration (in TUs)>, <offset (in TUs)>  
   
 csa   Send an 802.11h channel switch anouncement with chanspec:  
     <mode> <count> <channel>[a,b][n][u,l]  
     mode (0 or 1)  
     count (0-254)  
     channel number (0-224)  
     band a=5G, b=2G  
     bandwidth n=10, non for 20 & 40  
     ctl sideband, l=lower, u=upper, default no ctl sideband  
   
 constraint  
     Send an 802.11h Power Constraint IE  
     Usage: wl constraint 1-255 db  
   
 rm_req Request a radio measurement of type basic, cca, or rpi  
     specify a series of measurement types each followed by options.  
     example: wl rm_req cca -c 1 -d 50 cca -c 6 cca -c 11  
     Options:  
     -t n numeric token id for measurement set or measurement  
     -c n channel  
     -d n duration in TUs (1024 us)  
     -p  parallel flag, measurement starts at the same time as previous  
   
     Each measurement specified uses the same channel and duration as the  
     previous unless a new channel or duration is specified.  
   
 rm_rep Get current radio measurement report  
   
 join_pref  
     Set/Get join target preferences.  
   
 assoc_pref  
     Set/Get association preference.  
 Usage: wl assoc_pref [auto|a|b|g]  
   
 wme   Set WME (Wireless Multimedia Extensions) mode (0=off, 1=on, -1=auto)  
   
 wme_ac wl wme_ac ap|sta [be|bk|vi|vo [ecwmax|ecwmin|txop|aifsn|acm <value>] ...]  
   
 wme_apsd  
     Set APSD (Automatic Power Save Delivery) mode on AP (0=off, 1=on)  
   
 wme_apsd_sta  
     Set APSD parameters on STA. Driver must be down.  
 Usage: wl wme_apsd_sta <max_sp_len> <be> <bk> <vi> <vo>  
   <max_sp_len>: number of frames per USP: 0 (all), 2, 4, or 6  
   <xx>: value 0 to disable, 1 to enable U-APSD per AC  
   
 wme_dp Set AC queue discard policy.  
 Usage: wl wme_dp <be> <bk> <vi> <vo>  
   <xx>: value 0 for newest-first, 1 for oldest-first  
   
 wme_counters  
     print WMM stats  
   
 wme_clear_counters  
     clear WMM counters  
   
 wme_tx_params  
     wl wme_tx_params [be|bk|vi|vo [short|sfb|long|lfb|max_rate <value>] ...]  
   
 wme_maxbw_params  
     wl wme_maxbw_params [be|bk|vi|vo <value> ....]  
   
 lifetime  
     Set Lifetime parameter (milliseconds) for each ac.  
 wl lifetime be|bk|vi|vo [<value>]  
   
 reinit Reinitialize device  
   
 sta_info  
     wl sta_info <xx:xx:xx:xx:xx:xx>  
   
 cap   driver capabilities  
   
 malloc_dump  
     Deprecated. Folded under 'wl dump malloc  
   
 chan_info  
     channel info  
   
 add_ie Add a vendor proprietary IE to 802.11 management packets  
 Usage: wl add_ie <pktflag> length OUI hexdata  
 <pktflag>: Bit 0 - Beacons  
       Bit 1 - Probe Rsp  
       Bit 2 - Assoc/Reassoc Rsp  
       Bit 3 - Auth Rsp  
       Bit 4 - Probe Req  
       Bit 5 - Assoc/Reassoc Req  
 Example: wl add_ie 3 10 00:90:4C 0101050c121a03  
      to add this IE to beacons and probe responses  
   
 del_ie Delete a vendor proprietary IE from 802.11 management packets  
 Usage: wl del_ie <pktflag> length OUI hexdata  
 <pktflag>: Bit 0 - Beacons  
       Bit 1 - Probe Rsp  
       Bit 2 - Assoc/Reassoc Rsp  
       Bit 3 - Auth Rsp  
       Bit 4 - Probe Req  
       Bit 5 - Assoc/Reassoc Req  
 Example: wl del_ie 3 10 00:90:4C 0101050c121a03  
   
 list_ie Dump the list of vendor proprietary IEs  
   
 rand  Get a 2-byte Random Number from the MAC's PRNG  
 Usage: wl rand  
   
 otpw  Write an srom image to on-chip otp  
 Usage: wl otpw file  
   
 nvotpw Write nvram to on-chip otp  
 Usage: wl nvotpw file  
   
 bcmerrorstr  
     errorstring  
   
 freqtrack  
     Set Frequency Tracking Mode (0=Auto, 1=On, 2=OFF)  
   
 eventing  
     set/get 128-bit hex filter bitmask for MAC event reporting up to application layer  
   
 event_msgs  
     set/get 128-bit hex filter bitmask for MAC event reporting via packet indications  
   
 counters  
     Return driver counter values  
   
 delta_stats_interval  
     set/get the delta statistics interval in seconds (0 to disable)  
   
 delta_stats  
     get the delta statistics for the last interval  
   
 assoc_info  
     Returns the assoc req and resp information [STA only]  
   
 autochannel  
     auto channel selection:   
     1 to issue a channel scanning;  
     2 to set chanspec based on the channel scan result;  
     without argument to only show the chanspec selected;   
     ssid must set to null before this process, RF must be up  
   
 csscantimer  
     auto channel scan timer in minutes (0 to disable)  
   
 closed hides the network from active scans, 0 or 1.  
     0 is open, 1 is hide  
   
 pmkid_info  
     Returns the pmkid table  
   
 abminrate  
     get/set afterburner minimum rate threshold  
   
 bss   set/get BSS enabled status: up/down  
   
 closednet  
     set/get BSS closed network attribute  
   
 ap_isolate  
     set/get AP isolation  
   
 eap_restrict  
     set/get EAP restriction  
   
 diag  diag testindex(1-interrupt, 2-loopback, 3-memory, 4-led); precede by 'wl down' and follow by 'wl up'  
   
 reset_d11cnts  
     reset 802.11 MIB counters  
   
 staname get/set station name:   
     Maximum name length is 15 bytes  
   
 apname get AP name  
   
 otpdump Dump raw otp  
   
 otpstat Dump OTP status  
   
 nrate  -r legacy rate (CCK, OFDM)-m mcs index-s stf mode (0=SISO,1=CDD,2=STBC(not supported),3=SDM)-w Override mcs only to support STA's with/without STBC capability  
   
 mimo_txbw  
     get/set mimo txbw (2=20Mhz(lower), 3=20Mhz upper, 4=40Mhz, 5=40Mhz dup<mcs32 only)  
   
 cac_addts  
     add TSPEC, error if STA is not associated or WME is not enabled  
     arg: TSPEC parameter input list  
   
 cac_delts  
     delete TSPEC, error if STA is not associated or WME is not enabled  
     arg: TSINFO for the target tspec  
   
 cac_delts_ea  
     delete TSPEC, error if STA is not associated or WME is not enabled  
     arg1: Desired TSINFO for the target tspec  
     arg2: Desired MAC address  
   
 cac_tslist  
     Get the list of TSINFO in driver  
     eg. 'wl cac_tslist' get a list of TSINFO  
   
 cac_tslist_ea  
     Get the list of TSINFO for given STA in driver  
     eg. 'wl cac_tslist_ea ea' get a list of TSINFO  
   
 cac_tspec  
     Get specific TSPEC with matching TSINFO  
     eg. 'wl cac_tspec 0xaa 0xbb 0xcc' where 0xaa 0xbb & 0xcc are TSINFO octets  
   
 cac_tspec_ea  
     Get specific TSPEC for given STA with matching TSINFO  
     eg. 'wl cac_tspec 0xaa 0xbb 0xcc xx:xx:xx:xx:xx:xx'  
       where 0xaa 0xbb & 0xcc are TSINFO octets and xx is mac address  
   
 phy_txpwrindex  
     usage: (set) phy_txpwrindex core0_idx core1_idx core2_idx core3_idx    (get) phy_txpwrindex, return format: core0_idx core1_idx core2_idx core3_idxSet/Get txpwrindex  
   
 phy_test_tssi  
     wl phy_test_tssi val  
   
 phy_test_tssi_offs  
     wl phy_test_tssi_offs val  
   
 phy_rssiant  
     wl phy_rssiant antindex(0-3)  
   
 phy_rssi_ant  
     Get RSSI per antenna (only gives RSSI of current antenna for SISO PHY)  
   
 lpphy_papdepstbl  
     print papd eps table; Usage: wl lpphy_papdepstbl  
   
 rifs  set/get the rifs status; usage: wl rifs <1/0> (On/Off)  
   
 rifs_advert  
     set/get the rifs mode advertisement status; usage: wl rifs_advert <-1/0> (Auto/Off)  
   
 phy_rxiqest  
     Get phy RX IQ noise in dBm:  
     -s # of samples (2^n)  
     -a antenna select, 0,1 or 3  
   
 phy_txiqcc  
     usage: phy_txiqcc [a b]  
 Set/get the iqcc a, b values  
   
 phy_txlocc  
     usage: phy_txlocc [di dq ei eq fi fq]  
 Set/get locc di dq ei eq fi fq values  
   
 phytable  
     usage: wl phytable table_id offset width_of_table_element [table_element]  
 Set/get table element of a table with the given ID at the given offset  
 Note that table width supplied should be 8 or 16 or 32  
 table ID, table offset can not be negative  
   
 pavars Set/get temp PA parameters  
 usage: wl down  
     wl pavars pa2gw0a0=0x1 pa2gw1a0=0x2 pa2gw2a0=0x3 ...   
     wl pavars  
     wl up  
  override the PA parameters after driver attach(srom read), before diver up  
  These override values will be propogated to HW when driver goes up  
  PA parameters in one band range (2g, 5gl, 5g, 5gh) must all present if  
  one of them is specified in the command, otherwise it will be filled with 0  
   
 povars Set/get temp power offset  
 usage: wl down  
     wl povars cck2gpo=0x1 ofdm2gpo=0x2 mcs2gpo=0x3 ...   
     wl povars  
     wl up  
  override the power offset after driver attach(srom read), before diver up  
  These override values will be propogated to HW when driver goes up  
  power offsets in one band range (2g, 5gl, 5g, 5gh) must all present if  
  one of them is specified in the command, otherwise it will be filled with 0 cck(2g only), ofdm, and mcs(0-7) for NPHY are supported   
   
 fem   Set temp fem2g/5g value  
 usage: wl fem (tssipos2g=0x1 extpagain2g=0x2 pdetrange2g=0x1 triso2g=0x1 antswctl2g=0)  
     (tssipos5g=0x1 extpagain5g=0x2 pdetrange5g=0x1 triso5g=0x1 antswctl5g=0)  
   
 antgain Set temp ag0/1 value  
 usage: wl antgain ag0=0x1 ag1=0x2  
   
 maxpower  
     Set temp maxp2g(5g)a0(a1) value  
 usage: wl maxpower maxp2ga0=0x1 maxp2ga1=0x2 maxp5ga0=0xff maxp5ga1=0xff  
     maxp5gla0=0x3 maxp5gla1=0x4 maxp5gha0=0x5 maxp5gha1=0x6  
   
 phy_antsel  
     get/set antenna configuration   
     set: -1(AUTO), 0xAB(fixed antenna selection)  
         where A and B is the antenna numbers used for RF chain 1 and 0 respectively  
     query: <utx>[AUTO] <urx>[AUTO] <dtx>[AUTO] <drx>[AUTO]  
         where utx = TX unicast antenna configuration  
             urx = RX unicast antenna configuration  
             dtx = TX default (non-unicast) antenna configuration  
             drx = RX default (non-unicast) antenna configuration  
   
   
 txcore Usage: wl txcore -k <CCK core mask> -o <OFDM core mask> -s <1..4> -c <core bitmap>  
     -k CCK core mask  
     -o OFDM core mask  
     -s # of space-time-streams  
     -c active core (bitmask) to be used when transmitting frames  
   
 txchain_pwr_offset  
     Usage: wl txchain_pwr_offset [qdBm offsets]  
     Get/Set the current offsets for each core in qdBm (quarter dBm)  
   
 sample_collect  
     Optional parameters HTPHY/(NPHY with NREV >= 7) are:  
     -f File name to dump the sample buffer (default "sample_collect.dat")  
     -t Trigger condition (default now)  
          now, good_fcs, bad_fcs, bad_plcp, crs, crs_glitch, crs_deassert  
     -b PreTrigger duration in us (default 10)  
     -a PostTrigger duration in us (default 10)   
     -m Sample collect mode (default 1)   
          HTPHY: 0=adc, 1..3=adc+rssi, 4=gpio  
          NPHY: 1=Dual-Core adc[9:2], 2=Core0 adc[9:0], 3=Core1 adc[9:0], gpio=gpio  
     -g GPIO mux select (default 0)  
          use only for gpio mode  
     -d Downsample enable (default 0)  
          use only for HTPHY  
     -e BeDeaf enable (default 0)  
     -i Timeout in units of 10us (default 1000)  
 Optional parameters (NPHY with NREV < 7) are:  
     -f File name to dump the sample buffer (binary format, default "sample_collect.dat")  
     -u Sample collect duration in us (default 60)  
     -c Cores to do sample collect, only if BW=40MHz (default both)  
 For (NREV < 7), the NPHY buffer returned has the format:  
     In 20MHz [(uint16)num_bytes, <I(core0), Q(core0), I(core1), Q(core1)>]  
     In 40MHz [(uint16)num_bytes(core0), <I(core0), Q(core0)>,  
         (uint16)num_bytes(core1), <I(core1), Q(core1)>]  
   
 txfifo_sz  
     set/get the txfifo size; usage: wl txfifo_sz <fifonum> <size_in_bytes>  
   
 rate_histo  
     Get rate hostrogram  
   
 pkteng_start  
     start packet engine tx usage: wl pkteng_start <xx:xx:xx:xx:xx:xx> <tx|txwithack> [(async)|sync] [ipg] [len] [nframes] [src]  
     start packet engine rx usage: wl pkteng_start <xx:xx:xx:xx:xx:xx> <rx|rxwithack> [(async)|sync] [rxframes] [rxtimeout]  
     sync: synchronous mode  
     ipg: inter packet gap in us  
     len: packet length  
     nframes: number of frames; 0 indicates continuous tx test  
     src: source mac address  
     rxframes: number of receive frames (sync mode only)  
     rxtimeout: maximum timout in msec (sync mode only)  
   
 pkteng_stop  
     stop packet engine; usage: wl pkteng_stop <tx|rx>  
   
 pkteng_stats  
     packet engine stats; usage: wl pkteng_stats  
   
 wowl  Enable/disable WOWL events  
  0  - Clear all events  
 Bit 0 - Wakeup on Magic Packet  
 Bit 1 - Wakeup on NetPattern (use 'wl wowl_pattern' to configure pattern)  
 Bit 2 - Wakeup on loss-of-link due to Disassociation/Deauth  
 Bit 3 - Wakeup on retrograde tsf  
 Bit 4 - Wakeup on loss of beacon (use 'wl wowl_bcn_loss' to configure time)  
   
 wowl_bcn_loss  
     Set #of seconds of beacon loss for wakeup event  
   
 wowl_pattern  
     usage: wowl_pattern [ [clr | [[ add | del ] offset mask value ]]]  
 No options -- lists existing pattern list  
 add -- Adds the pattern to the list  
 del -- Removes a pattern from the list  
 clr -- Clear current list  
 offset -- Starting offset for the pattern  
 mask -- Mask to be used for pattern. Bit i of mask => byte i of the pattern  
 value -- Value of the pattern  
   
 wowl_wakeind  
     usage: wowl_wakeind [clear]  
 Shows last system wakeup event indications from PCI and D11 cores  
 clear - Clear the indications  
   
 wowl_status  
     usage: wowl_status [clear]  
 Shows last system wakeup setting  
   
 wowl_pkt  
     Send a wakeup frame to wakup a sleeping STA in WAKE mode  
 Usage: wl wowl_pkt <len> <dst ea | bcast | ucast <STA ea>>[ magic [<STA ea>] | net <offset> <pattern>]  
 e.g. To send bcast magic frame -- wl wowl_pkt 102 bcast magic 00:90:4c:AA:BB:CC  
    To send ucast magic frame -- wl wowl_pkt 102 ucast 00:90:4c:aa:bb:cc magic  
    To send a frame with L2 unicast - wl wowl_pkt 102 00:90:4c:aa:bb:cc net 0 0x00904caabbcc  
  NOTE: offset for netpattern frame starts from "Dest EA" of ethernet frame.So dest ea will be used only when offset is >= 6  
   
 wme_apsd_trigger  
     Set Periodic APSD Trigger Frame Timer timeout in ms (0=off)  
   
 wme_autotrigger  
     Enable/Disable sending of APSD Trigger frame when all ac are delivery enabled  
   
 reassoc Initiate a (re)association request.  
     Usage: wl reassoc <bssid> [options]  
     Options:  
     -c CL, --chanspecs=CL  chanspecs (comma or space separated list)  
   
 send_nulldata  
     Sed a null frame to the specified hw address  
   
 btc_params  
     g/set BT Coex parameters  
   
 btc_flags  
     g/set BT Coex flags  
   
 obss_scan_params  
     set/get Overlapping BSS scan parameters  
 Usage: wl obss_scan a b c d e ...; where  
     a-Passive Dwell, {5-1000TU}, default = 100  
     b-Active Dwell, {10-1000TU}, default = 20  
     c-Width Trigger Scan Interval, {10-900sec}, default = 300  
     d-Passive Total per Channel, {200-10000TU}, default = 200  
     e-Active Total per Channel, {20-1000TU}, default = 20  
     f-Channel Transition Delay Factor, {5-100}, default = 5  
     g-Activity Threshold, {0-100%}, default = 25  
   
 keep_alive  
     Send specified "keep-alive" packet periodically.  
     Usage: wl keep_alive <period> <packet>  
         period: Re-transmission period in milli-seconds. 0 to disable packet transmits.  
         packet: Hex packet contents to transmit. The packet contents should include the entire ethernet packet (ethernet header, IP header, UDP header, and UDP payload) specified in network byte order.  
   
     e.g. Send keep alive packet every 30 seconds:  
     wl keep_alive 30000 0x0014a54b164f000f66f45b7e08004500001e000040004011c52a0a8830700a88302513c413c4000a00000a0d  
   
 srchmem g/set ucode srch engine memory  
   
 pkt_filter_add  
     Install a packet filter.  
     Usage: wl pkt_filter_add <id> <polarity> <type> <offset> <bitmask> <pattern>  
     id:    Integer. User specified id.  
     type:   0 (Pattern matching filter).  
     offset:  Integer. Offset within received packets to start matching.  
     polarity: Set to 1 to negate match result. 0 is default.  
     bitmask: Hex bitmask that indicates which bits of 'pattern' to match. Must be same  
         size as 'pattern'. Bit 0 of bitmask corresponds to bit 0 of pattern, etc.  
         If bit N of bitmask is 0, then do *not* match bit N of the pattern with  
         the received payload. If bit N of bitmask is 1, then perform match.  
     pattern: Hex pattern to match.  
   
 pkt_filter_clear_stats  
     Clear packet filter statistic counter values.  
     Usage: wl pkt_filter_clear_stats <id>  
   
 pkt_filter_enable  
     Enable/disable a packet filter.  
     Usage: wl pkt_filter_enable <id> <0|1>  
   
 pkt_filter_list  
     List installed packet filters.  
     Usage: wl pkt_filter_list [val]  
     val: 0 (disabled filters) 1 (enabled filters)  
   
 pkt_filter_mode  
     Set packet filter match action.  
     Usage: wl pkt_filter_mode <value>  
     value: 1 - Forward packet on match, discard on non-match (default).  
         0 - Discard packet on match, forward on non-match.  
   
 pkt_filter_delete  
     Uninstall a packet filter.  
     Usage: wl pkt_filter_delete <id>  
   
 pkt_filter_stats  
     Retrieve packet filter statistic counter values.  
     Usage: wl pkt_filter_stats <id>  
   
 seq_start  
     Initiates command batching sequence. Subsequent IOCTLs will be queued until  
 seq_stop is received.  
   
 seq_stop  
     Defines the end of command batching sequence. Queued IOCTLs will be executed.  
   
 seq_delay  
     Driver should spin for the indicated amount of time.  
 It is only valid within the context of batched commands.  
   
 seq_error_index  
     Used to retrieve the index (starting at 1) of the command that failed within a batch  
   
 bmac_reboot  
     Reboot BMAC  
   
 txmcsset  
     get Transmit MCS rateset for 11N device  
   
 rxmcsset  
     get Receive MCS rateset for 11N device  
   
 mimo_ss_stf  
     get/set SS STF mode.  
     Usage: wl mimo_ss_stf <value> <-b a | b>  
     value: 0 - SISO; 1 - CDD  
     -b(band): a - 5G; b - 2.4G  
   
 assoclistinfo  
     AP only: Get the list of yet another form of associated station info  
   
 scblist AP only: Get STA list  
   
 assertlog  
     get external assert logs  
     Usage: wl assertlog  
   
 assert_type  
     set/get the asset_bypass flag; usage: wl assert_type <1/0> (On/Off)  
   
 ledbh  set/get led behavior  
     Usage: wl ledbh [0-3] [0-15]  
   
 obss_coex_action  
     send OBSS 20/40 Coexistence Mangement Action Frame  
     Usage: wl obss_coex_action -i <1/0> -w <1/0> -c <channel list>  
      -i: 40MHz intolerate bit; -w: 20MHz width Req bit;  
      -c: channel list, 1 - 14  
      At least one option must be provided  
   
 chanim_state  
     get channel interference state  
     Usage: wl chanim_state channel  
     Valid channels: 1 - 14  
     returns: 0 - Acceptable; 1 - Severe  
   
 chanim_mode  
     get/set channel interference measure (chanim) mode  
     Usage: wl chanim_mode <value>  
     value: 0 - disabled; 1 - detection only; 2 - detection and avoidance  
   
 ledbh  set/get led behavior  
     Usage: wl ledbh [0-3] [0-15]  
   
 led_blink_sync  
     set/get led_blink_sync  
     Usage: wl led_blink_sync [0-3] [0/1]  
   
 cca_get_stats  
     Usage: wl cca_stats [-c channel] [-s num seconds][-a]  
      -c channel: Optional. specify channel. 0 = All channels. Default = current channel   
      -s num_seconds: Optional. Default = 10, Max = 60  
      -i: list individual measurements in addition to the averages  
      -curband: Only recommend channels on current band  
   
 itfr_get_stats  
     get interference source information  
   
 itfr_enab  
     get/set STA interference detection mode(STA only)  
      0 - disable  
      1 - enable maual detection  
      2 - enable auto detection  
   
 itfr_detect  
     issue an interference detection request  
   
 smfstats  
     get/clear selected management frame (smf) stats wl smfstats [-C num]|[--cfg=num] [auth]|[assoc]|[reassoc]|[clear]  
     clear - to clear the stats  
   
 manfinfo  
     show chip package info in OTP  
   
 rrm_nbr_req  
     send 11k neighbor report measurement request  
     Usage: wl 11k_nbr_req <da> [ssid]  
   
 pm_dur Retrieve accumulated PM duration information (GET) or clear accumulator (SET)  
     Usage: wl pm_dur <any-number-to-clear>  
   
 mpc_dur Retrieve accumulated MPC duration information in ms (GET) or clear accumulator (SET)  
     Usage: wl mpc_dur <any-number-to-clear>  
   
 chanim_acs_record  
     get the auto channel scan record.   
      Usage: wl acs_record  
   
 dngl_wd enable or disable dongle watchdog timer  
     Usage: wl dngl_wd <on/off>(to turn on\off) <exptime in sec>  
   
 tsf   set/get tsf register  
     Usage: wl tsf [<high> <low>]  
   
 tpc_mode  
     Enable/disable AP TPC.  
 Usage: wl tpc_mode <mode>   
     0 - disable, 1 - BSS power control, 2 - AP power control, 3 - Both (1) and (2)  
   
   
 tpc_period  
     Set AP TPC periodicity in secs.  
 Usage: wl tpc_period <secs>   
   
   
 tpc_lm Get current link margins.  
   
   
 mfp_sa_query  
     Send a sa query req/resp to a peer  
     usage: wl mfp_sa_query <Dest Mac Addr> action id flag  
   
 mfp_disassoc  
     send bogus disassoc  
 Usage: wl mfp_disassoc  
   
   
 mfp_deauth  
     send bogus deauth  
     Usage: wl mfp_dedauth  
   
   
 mfp_assoc  
     send assoc  
 Usage: wl mfp_assoc  
   
   
 mfp_auth  
     send auth  
     Usage: wl mfp_auth  
   
   
 mfp_reassoc  
     send reassoc  
 Usage: wl mfp_reassoc  
   
   
 monitor_lq  
     Start/Stop monitoring link quality metrics - RSSI and SNR  
     Usage: wl monitor_lq <0: turn off / 1: turn on  
   
   
 monitor_lq_status  
     Returns averaged link quality metrics - RSSI and SNR values  
   
 scb_probe  
     Set probing parameters for inactive clients.  
     <timout in seconds> <activity_time in seconds> <max number of probes>  
   
 rpmt  rpmt <pm1-to> <pm0-to>  
   
   
 spatial_policy  
     set/get spatial_policy  
     Usage: wl spatial_policy <-1: auto / 0: turn off / 1: turn on>  
         to control individual band/sub-band use  
         wl spatial_policy a b c d e  
         where a is 2.4G band setting  
         where b is 5G lower band setting  
         where c is 5G middle band setting  
         where d is 5G high band setting  
         where e is 5G upper band setting  
   
   
  >   

Comments

  1. Hi. Please help. What command should I reconnect to the Internet?

    ReplyDelete
  2. What is the command for changing password in cli

    ReplyDelete
    Replies
    1. Hello!

      That would be the "passwd" command to change the password for Telnet.


      Regards,
      Ahmed

      Delete

Post a Comment

Popular posts from this blog

Technicolor TG582n: Info, Configuration and Usage Options

Hi! DANT-T and DANT-1 variants DANT-T and DANT-1 variants The Technicolor TG582n ( quick specs , user guide ) seems to be quite popular with ISPs and can be found in branded, sometimes locked*, form throughout. Fortunately, it works really well once properly configured and it is (usually) easy to unlock by flashing it with an unlocked firmware. One thing to take into consideration is that it comes in two main variants, the DANT-1 and DANT-T, with each variant only accepting it's own firmware (unless you are installing OpenWRT ). Firmware Update: Now, when it comes to flashing the firmware, we need: (Windows 7 is recommended) - Thomson Upgrade Wizard   - User privileges (username and password for user authorized to flash firmware ... for some branded ones we don't need one once router has been reset but for some like O2 we need the user SuperUser with password the Serial Number of router) - (Unlocked/Generic) Firmware for the

BT Home Hub v2 Type A: Info, Unlock & Configuration

Hello Again! Next up is the BT Home Hub v2* Type A home ADSL Wireless Router by Thomson/Technicolor (more info at OpenWRT wiki ). Again, this router accepts only BT specific/approved domain names for username of dsl and must be 'unlocked' to be used with other ISPs. Such 'unlocking' (thanks to btsimonh and Surreliz3) also allows more configuration options, though firmware upgrade options might become limited. As with the BTHH v1 & v1.5 , this router can be 'unlocked' via jTAG method but there is also the relatively easier software method provided the firmware version currently on the BTHHv2A is lower than version 8.1.H.U.  Unlock: I 'unlocked' mine via the software method a long time ago so I won't be able to post screenshots of the process (have yet to try the jtag method on one with newer firmware that I also happen to have), but, here is the process as described on the now defunct psidoc.com website (the links may

PTCL's (newer) Wireless n 150mbps W150D xDSL Router by Tenda Part2

From the hardware point of view, the PTCL/Tenda W150D is not much different from other BCM6328 based routers but the difference surely lies in the software/firmware ... so let's take a look at the gui side of things ... From the start it was apparent that the firmware for PTCL was not 'special/locked' one and just used image replacement replacing Tenda's images/logos with those for PTCL ... anyways it also didn't seem to work well, felt kind of like a beta version of the firmware ... couldn't hold onto some settings ... my long line and difficult stats didn't help either (awaiting conversion from copper to fiber) ... so in desperation I looked at firmware updates for the router on Tenda's website knowing full well that a corrupted/interrupted/slightly-changed firmware update would brick the router with no obvious way to recover as serial & jTAG pinouts are not known (there are some test points ... but lack of interest) and no full flash backup c