With Telnet access, more options become available that are not accessible via the web interface! Since the router uses the Broadcom chipset, we can apply almost all the same tweaks as documented for other Broadcom based routers:
Here is the list of commands (Password is the one set by you):
There is also Shell access:
With regards to dsl modem, the commands "adsl" and "xdslctl" are important though anyone of these can be used!
continues ...
In the next part, we'll take a look at some SNR tweaking and Stability options for the modem part and perhaps we'll look at the wireless section "wlctl" as well!
Here is the list of commands (Password is the one set by you):
BCM96328 Broadband Router
Login: admin
Password:
> ?
?
help
logout
exit
quit
reboot
adsl
xdslctl
xtm
brctl
cat
loglevel
logdest
virtualserver
ddns
syslog
echo
ifconfig
ping
ps
pwd
sntp
sysinfo
tftp
wlctl
arp
defaultgateway
dhcpserver
dns
lan
lanhosts
passwd
ppp
restoredefault
route
save
swversion
cfgupdate
swupdate
exitOnIdle
wan
There is also Shell access:
> sh
BusyBox v1.00 (2012.05.30-12:11+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
With regards to dsl modem, the commands "adsl" and "xdslctl" are important though anyone of these can be used!
> xdslctl
Usage: xdslctl start [--up] [--mod <a|d|l|t|2|p|e|m|M3|M5>] [--lpair <(i)nner|(o)uter>]
[--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>]
[--sra <on|off>] [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt <0xBitMap-UsDs>]
[--Ginp <0xBitMap-UsDs>] [--TpsTc <0xBitMap-AvPvAaPa>] [--monitorTone <on|off>]
[--forceJ43 <on|off>] [--toggleJ43B43 <on|off>]
xdslctl stop
xdslctl connection [--up] [--down] [--loopback] [--reverb]
[--medley] [--noretrain] [--L3] [--diagmode] [--L0]
[--tones] [--normal] [--freezeReverb] [--freezeMedley]
xdslctl configure [--mod <a|d|l|t|2|p|e|m|M3|M5>] [--lpair <(i)nner|(o)uter>]
[--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>]
[--sra <on|off>] [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt <0xBitMap-UsDs>]
[--Ginp <0xBitMap-UsDs>] [--TpsTc <0xBitMap-AvPvAaPa>] [--monitorTone <on|off>]
[--forceJ43 <on|off>] [--toggleJ43B43 <on|off>]
xdslctl bert [--start <#seconds>] [--stop] [--show]
xdslctl afelb [--time <sec>] [--tones] [--signal <1/2/8>]
xdslctl qlnmntr [--time <sec>] [--freq <msec>]
xdslctl inm [--start <BB_THRESH 10*dB> <INMIATO> <INMIATS>] [--stop] [--show]
xdslctl snrclamp [--shape <shapeId>] [--bpshape [bpIndex-bpLevel,]]
xdslctl nlnm [--show ] [--setThld <Thld_Num_Tones>]
xdslctl diag [--logstart <nBytes>] [--logpause] [--logstop] [--loguntilbufferfull <nBytes>]
[--loguntilretrain <nBytes>]
xdslctl info [--state] [--show] [--stats] [--SNR] [--QLN] [--Hlog] [--Hlin] [--HlinS] [--Bits]
[--linediag] [--reset] [--vendor] [--cfg]
xdslctl profile [--show] [--save] [--restore]
xdslctl --version
xdslctl --help
continues ...
In the next part, we'll take a look at some SNR tweaking and Stability options for the modem part and perhaps we'll look at the wireless section "wlctl" as well!
> wlctl
Usage: wlctl [-a|i <adapter>] [-h] [-d|u|x] <command> [arguments]
-h this message and command descriptions
-h [cmd] command description for cmd
-a, -i adapter name or number
-d output format signed integer
-u output format unsigned integer
-x output format hexdecimal
ver get version information
cmds generate a short list of available commands
up reinitialize and mark adapter up (operational)
down reset and mark adapter down (disabled)
out mark adapter down but do not reset hardware(disabled)
On dualband cards, cards must be bandlocked before use.
clk set board clock state. return error for set_clk attempt if the driver is not down
0: clock off
1: clock on
restart Restart driver. Driver must already be down.
reboot Reboot platform
radio Set the radio on or off.
"on" or "off"
dump Give suboption "list" to list various suboptions
srclear Clears first 'len' bytes of the srom, len in decimal or hex
Usage: srclear <len>
srdump print contents of SPROM to stdout
srwrite Write the srom: srwrite byteoffset value
srcrc Get the CRC for input binary file
ciswrite
Write specified <file> to the SDIO CIS source (either SROM or OTP)
cisupdate
Write a hex byte stream to specified byte offset to the CIS source (either SROM or OTP)
--preview option allows you to review the update without committing it
<byte offset> <hex byte stream> [--preview]
cisdump Display the content of the SDIO CIS source
-b <file> -- also write raw bytes to <file>
<len> -- optional count of bytes to display (must be even)
cis_source
Display which source is used for the SDIO CIS
cisconvert
Print CIS tuple for given name=value pair
rdvar Read a named variable to the srom
wrvar Write a named variable to the srom
nvram_source
Display which source is used for nvram
nvram_dump
print nvram variables to stdout
nvset set an nvram variable
name=value (no spaces around '=')
nvget get the value of an nvram variable
nvram_get
get the value of an nvram variable
revinfo get hardware revision information
customvar1
print the value of customvar1 in hex format
msglevel
set driver console debugging message bitvector
type 'wl msglevel ?' for values
phymsglevel
set phy debugging message bitvector
type 'wl phymsglevel ?' for values
PM set driver power management mode:
0: CAM (constantly awake)
1: PS (power-save)
2: FAST PS mode
wake set driver power-save mode sleep state:
0: core-managed
1: awake
promisc set promiscuous mode ethernet address reception
0 - disable
1 - enable
monitor set monitor mode
0 - disable
1 - enable active monitor mode (interface still operates)
frag Deprecated. Use fragthresh.
rts Deprecated. Use rtsthresh.
cwmin Set the cwmin. (integer [1, 255])
cwmax Set the cwmax. (integer [256, 2047])
srl Set the short retry limit. (integer [1, 255])
lrl Set the long retry limit. (integer [1, 255])
rate force a fixed rate:
valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
valid values for 802.11b are (1, 2, 5.5, 11)
valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
-1 (default) means automatically determine the best rate
mrate force a fixed multicast rate:
valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
valid values for 802.11b are (1, 2, 5.5, 11)
valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
-1 (default) means automatically determine the best rate
a_rate force a fixed rate for the A PHY:
valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
-1 (default) means automatically determine the best rate
a_mrate force a fixed multicast rate for the A PHY:
valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
-1 (default) means automatically determine the best rate
bg_rate force a fixed rate for the B/G PHY:
valid values for 802.11b are (1, 2, 5.5, 11)
valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
-1 (default) means automatically determine the best rate
bg_mrate
force a fixed multicast rate for the B/G PHY:
valid values for 802.11b are (1, 2, 5.5, 11)
valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
-1 (default) means automatically determine the best rate
infra Set Infrastructure mode: 0 (IBSS) or 1 (Infra BSS)
ap Set AP mode: 0 (STA) or 1 (AP)
bssid Get the BSSID value, error if STA and not associated
bssmax get number of BSSes
channel Set the channel:
valid channels for 802.11b/g (2.4GHz band) are 1 through 14
valid channels for 802.11a (5 GHz band) are:
36, 40, 44, 48, 52, 56, 60, 64,
100, 104, 108, 112, 116,120, 124, 128, 132, 136, 140,
149, 153, 157, 161,
184, 188, 192, 196, 200, 204, 208, 212, 216
cur_mcsset
Get the current mcs set
chanspecs
Get all the valid chanspecs (default: all within current locale):
-b band (5(a) or 2(b/g))
-w bandwidth, 10,20 or 40
[-c country_abbrev]
chanspec
Set <channel>[a,b][n][u,l]
channel number (0-224)
band a=5G, b=2G, default to 2G if channel <= 14
bandwidth, n=10, none for 20 & 40
ctl sideband, l=lower, u=upper
OR Set channel with legacy format:
-c channel number (0-224)
-b band (5(a) or 2(b/g))
-w bandwidth, 10,20 or 40
-s ctl sideband, -1=lower, 0=none, 1=upper
dfs_channel_forced
Set <channel>[a,b][n][u,l]
channel number (0-224)
band a=5G, b=2G, default to 2G if channel <= 14
bandwidth, n=10, non for 20 & 40
ctl sideband, l=lower, u=upper
tssi Get the tssi value from radio
txpwr Set tx power in milliwatts. Range [1, 84].
txpwr1 Set tx power in in various units. Choose one of (default: dbm):
-d dbm units
-q quarter dbm units
-m milliwatt units
Can be combined with:
-o turn on override to disable regulatory and other limitations
Use wl txpwr -1 to restore defaults
txpathpwr
Turn the tx path power on or off on 2050 radios
txpwrlimit
Return current tx power limit
powerindex
Set the transmit power for A band(0-63).
-1 - default value
atten Set the transmit attenuation for B band. Args: bb radio txctl1.
auto to revert to automatic control
manual to supspend automatic control
phyreg Get/Set a phy register:
offset [ value ] [ band ]
radioreg
Get/Set a radio register:
offset [ value ] [ band/core ]
HTPHY:
Get a radio register: wl radioreg [ offset ] [ cr0/cr1/cr2 ]
Set a radio register: wl radioreg [ offset ] [ value ] [ cr0/cr1/cr2/all ]
ucflags Get/Set ucode flags 1, 2, 3(16 bits each)
offset [ value ] [ band ]
shmem Get/Set a shared memory location:
offset [ value ] [band ]
macreg Get/Set any mac registers(include IHR and SB):
macreg offset size[2,4] [ value ] [ band ]
ucantdiv
Enable/disable ucode antenna diversity (1/0 or on/off)
gpioout Set any GPIO pins to any value. Use with caution as GPIOs would be assigned to chipcommon
Usage: gpiomask gpioval
devpath print device path
pcieserdesreg
g/set SERDES registers: dev offset [val]
ampdu_activate_test
actiate
ampdu_tid
enable/disable per-tid ampdu; usage: wl ampdu_tid <tid> [0/1]
ampdu_retry_limit_tid
Set per-tid ampdu retry limit; usage: wl ampdu_retry_limit_tid <tid> [0~31]
ampdu_rr_retry_limit_tid
Set per-tid ampdu regular rate retry limit; usage: wl ampdu_rr_retry_limit_tid <tid> [0~31]
ampdu_send_addba
send addba to specified ea-tid; usage: wl ampdu_send_addba <tid> <ea>
ampdu_send_delba
send delba to specified ea-tid; usage: wl ampdu_send_delba <tid> <ea>
ampdu_clear_dump
clear ampdu counters
dpt_deny
adds/removes ea to dpt deny list
usage: wl dpt_deny <add,remove> <ea>
dpt_endpoint
creates/updates/deletes dpt endpoint for ea
usage: wl dpt_endpoint <create, update, delete> <ea>
dpt_pmk sets DPT pre-shared key
dpt_fname
sets/gets DPT friendly name
dpt_list
gets status of all dpt peers
actframe
Send a Vendor specific Action frame to a channel
usage: wl actframe <Dest Mac Addr> <data> channel dwell-time <BSSID>
antdiv Set antenna diversity for rx
0 - force use of antenna 0
1 - force use of antenna 1
3 - automatic selection of antenna diversity
txant Set the transmit antenna
0 - force use of antenna 0
1 - force use of antenna 1
3 - use the RX antenna selection that was in force during
the most recently received good PLCP header
plcphdr Set the plcp header.
"long" or "auto" or "debug"
phytype Get phy type
rateparam
set driver rate selection tunables
arg 1: tunable id
arg 2: tunable value
wepstatus
Set or Get WEP status
wepstatus [on|off]
primary_key
Set or get index of primary key
addwep Set an encryption key. The key must be 5, 13 or 16 bytes long, or
10, 26, 32, or 64 hex digits long. The encryption algorithm is
automatically selected based on the key size. keytype is accepted
only when key length is 16 bytes/32 hex digits and specifies
whether AES-OCB or AES-CCM encryption is used. Default is ccm.
WAPI is selected if key len is 32 and arguments contain wapi.
addwep <keyindex> <keydata> [ocb | ccm | wapi] [notx] [xx:xx:xx:xx:xx:xx]
rmwep Remove the encryption key at the specified key index.
keys Prints a list of the current WEP keys
tsc Print Tx Sequence Couter for key at specified key index.
wsec_test
Generate wsec errors
wsec_test <test_type> <keyindex|xx:xx:xx:xx:xx:xx>
type 'wl wsec_test ?' for test_types
tkip_countermeasures
Enable or disable TKIP countermeasures (TKIP-enabled AP only)
0 - disable
1 - enable
wsec_restrict
Drop unencrypted packets if WSEC is enabled
0 - disable
1 - enable
eap restrict traffic to 802.1X packets until 802.1X authorization succeeds
0 - disable
1 - enable
cur_etheraddr
Get/set the current hw address
perm_etheraddr
Get the permanent address from NVRAM
authorize
restrict traffic to 802.1X packets until 802.1X authorization succeeds
deauthorize
do not restrict traffic to 802.1X packets until 802.1X authorization succeeds
deauthenticate
deauthenticate a STA from the AP with optional reason code (AP ONLY)
wsec wireless security bit vector
1 - WEP enabled
2 - TKIP enabled
4 - AES enabled
8 - WSEC in software
0x80 - FIPS enabled
0x100 - WAPI enabled
auth set/get 802.11 authentication type. 0 = OpenSystem, 1= SharedKey, 2=Open/Shared
wpa_auth
Bitvector of WPA authorization modes:
1 WPA-NONE
2 WPA-802.1X/WPA-Professional
4 WPA-PSK/WPA-Personal
64 WPA2-802.1X/WPA2-Professional
128 WPA2-PSK/WPA2-Personal
0 disable WPA
wpa_cap set/get 802.11i RSN capabilities
set_pmk Set passphrase for PMK in driver-resident supplicant.
scan Initiate a scan.
Default to an active scan across all channels for any SSID.
Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
Options:
-s S, --ssid=S SSIDs to scan
-t ST, --scan_type=ST [active|passive|prohibit] scan type
--bss_type=BT [bss/infra|ibss/adhoc] bss type to scan
-b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
-n N, --nprobes=N number of probes per scanned channel
-a N, --active=N dwell time per channel for active scanning
-p N, --passive=N dwell time per channel for passive scanning
-h N, --home=N dwell time for the home channel between channel scans
-c L, --channels=L comma or space separated list of channels to scan
iscan_s Initiate an incremental scan.
Default to an active scan across all channels for any SSID.
Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
Options:
-s S, --ssid=S SSIDs to scan
-t ST, --scan_type=ST [active|passive|prohibit] scan type
--bss_type=BT [bss/infra|ibss/adhoc] bss type to scan
-b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
-n N, --nprobes=N number of probes per scanned channel
-a N, --active=N dwell time per channel for active scanning
-p N, --passive=N dwell time per channel for passive scanning
-h N, --home=N dwell time for the home channel between channel scans
-c L, --channels=L comma or space separated list of channels to scan
iscan_c Continue an incremental scan.
Default to an active scan across all channels for any SSID.
Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
Options:
-s S, --ssid=S SSIDs to scan
-t ST, --scan_type=ST [active|passive|prohibit] scan type
--bss_type=BT [bss/infra|ibss/adhoc] bss type to scan
-b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
-n N, --nprobes=N number of probes per scanned channel
-a N, --active=N dwell time per channel for active scanning
-p N, --passive=N dwell time per channel for passive scanning
-h N, --home=N dwell time for the home channel between channel scans
-c L, --channels=L comma or space separated list of channels to scan
scancache_clear
clear the scan cache
escan Start an escan.
Default to an active scan across all channels for any SSID.
Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
Options:
-s S, --ssid=S SSIDs to scan
-t ST, --scan_type=ST [active|passive|prohibit] scan type
--bss_type=BT [bss/infra|ibss/adhoc] bss type to scan
-b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
-n N, --nprobes=N number of probes per scanned channel
-a N, --active=N dwell time per channel for active scanning
-p N, --passive=N dwell time per channel for passive scanning
-h N, --home=N dwell time for the home channel between channel scans
-c L, --channels=L comma or space separated list of channels to scan
escanabort
Abort an escan.
Default to an active scan across all channels for any SSID.
Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
Options:
-s S, --ssid=S SSIDs to scan
-t ST, --scan_type=ST [active|passive|prohibit] scan type
--bss_type=BT [bss/infra|ibss/adhoc] bss type to scan
-b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
-n N, --nprobes=N number of probes per scanned channel
-a N, --active=N dwell time per channel for active scanning
-p N, --passive=N dwell time per channel for passive scanning
-h N, --home=N dwell time for the home channel between channel scans
-c L, --channels=L comma or space separated list of channels to scan
passive Puts scan engine into passive mode
regulatory
Get/Set regulatory domain mode (802.11d). Driver must be down.
spect Get/Set 802.11h Spectrum Management mode.
0 - Off
1 - Loose interpretation of 11h spec - may join non-11h APs
2 - Strict interpretation of 11h spec - may not join non-11h APs
3 - Disable 11h and enable 11d
4 - Loose interpretation of 11h+d spec - may join non-11h APs
scanabort
Abort a scan.
scanresults
Return results from last scan.
iscanresults
Return results from last iscan. Specify a buflen (max 8188)
to artificially limit the size of the results buffer.
iscanresults [buflen]
assoc Print information about current network association.
(also known as "status")
status Print information about current network association.
(also known as "assoc")
disassoc
Disassociate from the current BSS/IBSS.
chanlist
Deprecated. Use channels.
channels
Return valid channels for the current settings.
channels_in_country
Return valid channels for the country specified.
Arg 1 is the country abbreviation
Arg 2 is the band(a or b)
curpower
Return current tx power settings.
-q (quiet): estimated power only.
curppr Return current tx power per rate offset.
txinstpwr
Return tx power based on instant TSSI
scansuppress
Suppress all scans for testing.
0 - allow scans
1 - suppress scans
evm Start an EVM test on the given channel, or stop EVM test.
Arg 1 is channel number 1-14, or "off" or 0 to stop the test.
Arg 2 is optional rate (1, 2, 5.5 or 11)
rateset Returns or sets the supported and basic rateset, (b) indicates basic
With no args, returns the rateset. Args are
rateset "default" | "all" | <arbitrary rateset> -m <arbitrary mcsset>
default - driver defaults
all - all rates are basic rates
arbitrary rateset - list of rates
arbitrary mcsset - list of mcs rates octets, each bit representing
corresponding mcs
List of rates are in Mbps and each rate is optionally followed
by "(b)" or "b" for a Basic rate. Example: 1(b) 2b 5.5 11
At least one rate must be Basic for a legal rateset.
roam_trigger
Get or Set the roam trigger RSSI threshold:
Get: roam_trigger [a|b]
Set: roam_trigger <integer> [a|b|all]
integer - 0: default
1: optimize bandwidth
2: optimize distance
[-1, -99]: dBm trigger value
roam_delta
Set the roam candidate qualification delta. roam_delta [integer [, a/b]]
roam_scan_period
Set the roam candidate qualification delta. (integer)
suprates
Returns or sets the 11g override for the supported rateset
With no args, returns the rateset. Args are a list of rates,
or 0 or -1 to specify an empty rateset to clear the override.
List of rates are in Mbps, example: 1 2 5.5 11
scan_channel_time
Get/Set scan channel time
scan_unassoc_time
Get/Set unassociated scan channel dwell time
scan_home_time
Get/Set scan home channel dwell time
scan_passive_time
Get/Set passive scan channel dwell time
scan_nprobes
Get/Set scan parameter for number of probes to use per channel scanned
prb_resp_timeout
Get/Set probe response timeout
channel_qa
Get last channel quality measurment
channel_qa_start
Start a channel quality measurment
country Select Country Code for driver operational region
For simple country setting: wl country <country>
Where <country> is either a long name or country code from ISO 3166; for example "Germany" or "DE"
For a specific built-in country definition: wl country <built-in> [<advertised-country>]
Where <built-in> is a country country code followed by '/' and regulatory revision number.
For example, "US/3".
And where <advertised-country> is either a long name or country code from ISO 3166.
If <advertised-country> is omitted, it will be the same as the built-in country code.
Use 'wl country list [band(a or b)]' for the list of supported countries
country_ie_override
To set/get country ie
autocountry_default
Select Country Code for use with Auto Contry Discovery
join Join a specified network SSID.
Usage: join <ssid> [key <0-3>:xxxxx] [imode bss|ibss] [amode open|shared|openshared|wpa|wpapsk|wpa2|wpa2psk|wpanone] [options]
Options:
-b MAC, --bssid=MAC BSSID (xx:xx:xx:xx:xx:xx) to scan and join
-c CL, --chanspecs=CL chanspecs (comma or space separated list)
ssid Set or get a configuration's SSID.
wl ssid [-C num]|[--cfg=num] [<ssid>]
If the configuration index 'num' is not given, configuraion #0 is assumed and
setting will initiate an assoication attempt if in infrastructure mode,
or join/creation of an IBSS if in IBSS mode,
or creation of a BSS if in AP mode.
mac Set or get the list of source MAC address matches.
wl mac xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]
To Clear the list: wl mac none
macmode Set the mode of the MAC list.
0 - Disable MAC address matching.
1 - Deny association to stations on the MAC list.
2 - Allow association to stations on the MAC list.
wds Set or get the list of WDS member MAC addresses.
Set using a space separated list of MAC addresses.
wl wds xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]
lazywds Set or get "lazy" WDS mode (dynamically grant WDS membership to anyone).
noise Get noise (moving average) right after tx in dBm
fqacurcy
Manufacturing test: set frequency accuracy mode.
freqacuracy syntax is: fqacurcy <channel>
Arg is channel number 1-14, or 0 to stop the test.
crsuprs Manufacturing test: set carrier suppression mode.
carriersuprs syntax is: crsuprs <channel>
Arg is channel number 1-14, or 0 to stop the test.
longtrain
Manufacturing test: set longtraining mode.
longtrain syntax is: longtrain <channel>
Arg is A band channel number or 0 to stop the test.
band Returns or sets the current band
auto - auto switch between available bands (default)
a - force use of 802.11a band
b - force use of 802.11b band
bands Return the list of available 802.11 bands
phylist Return the list of available phytypes
shortslot
Get current 11g Short Slot Timing mode. (0=long, 1=short)
shortslot_override
Get/Set 11g Short Slot Timing mode override. (-1=auto, 0=long, 1=short)
shortslot_restrict
Get/Set AP Restriction on associations for 11g Short Slot Timing capable STAs.
0 - Do not restrict association based on ShortSlot capability
1 - Restrict association to STAs with ShortSlot capability
ignore_bcns
AP only (G mode): Check for beacons without NONERP element(0=Examine beacons, 1=Ignore beacons)
pktcnt Get the summary of good and bad packets.
upgrade Upgrade the firmware on an embedded device
gmode Set the 54g Mode (LegacyB|Auto||GOnly|BDeferred|Performance|LRS)
gmode_protection
Get G protection mode. (0=disabled, 1=enabled)
gmode_protection_control
Get/Set 11g protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)
gmode_protection_override
Get/Set 11g protection mode override. (-1=auto, 0=disable, 1=enable)
protection_control
Get/Set protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)
legacy_erp
Get/Set 11g legacy ERP inclusion (0=disable, 1=enable)
scb_timeout
AP only: inactivity timeout value for authenticated stas
assoclist
AP only: Get the list of associated MAC addresses.
isup Get driver operational state (0=down, 1=up)
rssi Get the current RSSI val, for an AP you must specify the mac addr of the STA
rssi_event
Set parameters associated with RSSI event notification
usage: wl rssi_event <rate_limit> <rssi_levels>
rate_limit: Number of events posted to application will be limited to 1 per this rate limit. Set to 0 to disable rate limit.
rssi_levels: Variable number of RSSI levels (maximum 8) in increasing order (e.g. -85 -70 -60). An event will be posted each time the RSSI of received beacons/packets crosses a level.
fasttimer
Deprecated. Use fast_timer.
slowtimer
Deprecated. Use slow_timer.
glacialtimer
Deprecated. Use glacial_timer.
radar Enable/Disable radar
radarargs
Get/Set Radar parameters in
order as version, npulses, ncontig, min_pw, max_pw, thresh0,
thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp,
min_fm_lp, max_span_lp, min_deltat, max_deltat,
autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra,
npulses_stg2, npulses_stg3, percal_mask, quant,
min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask
radarargs40
Get/Set Radar parameters for 40Mhz channel in
order as version, npulses, ncontig, min_pw, max_pw, thresh0,
thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp,
min_fm_lp, max_span_lp, min_deltat, max_deltat,
autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra,
npulses_stg2, npulses_stg3, percal_mask, quant,
min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask
radarthrs
Set Radar threshold for both 20 & 40MHz BW:
order as thresh0_20_lo, thresh1_20_lo, thresh0_40_lo, thresh1_40_lo
thresh0_20_hi, thresh1_20_hi, thresh0_40_hi, thresh1_40_hi
dfs_status
Get dfs status
interference
Get/Set interference mitigation mode. Choices are:
0 = none
1 = non wlan
2 = wlan manual
3 = wlan automatic
4 = wlan automatic with noise reduction
interference_override
Get/Set interference mitigation override. Choices are:
0 = no interference mitigation
1 = non wlan
2 = wlan manual
3 = wlan automatic
4 = wlan automatic with noise reduction
-1 = remove override, override disabled
frameburst
Disable/Enable frameburst mode
pwr_percent
Get/Set power output percentage
toe Enable/Disable tcpip offload feature
toe_ol Get/Set tcpip offload components
toe_stats
Display checksum offload statistics
toe_stats_clear
Clear checksum offload statistics
arpoe Enable/Disable arp agent offload feature
arp_ol Get/Set arp offload components
arp_peerage
Get/Set age of the arp entry in minutes
arp_table_clear
Clear arp cache
arp_hostip
Add a host-ip address or display them
arp_hostip_clear
Clear all host-ip addresses
arp_stats
Display ARP offload statistics
arp_stats_clear
Clear ARP offload statistics
wet Get/Set wireless ethernet bridging mode
bi Get/Set the beacon period (bi=beacon interval)
dtim Get/Set DTIM
wds_remote_mac
Get WDS link remote endpoint's MAC address
wds_wpa_role_old
Get WDS link local endpoint's WPA role (old)
wds_wpa_role
Get/Set WDS link local endpoint's WPA role
authe_sta_list
Get authenticated sta mac address list
autho_sta_list
Get authorized sta mac address list
measure_req
Send an 802.11h measurement request.
Usage: wl measure_req <type> <target MAC addr>
Measurement types are: TPC, Basic, CCA, RPI
Target MAC addr format is xx:xx:xx:xx:xx:xx
quiet Send an 802.11h quiet command.
Usage: wl quiet <TBTTs until start>, <duration (in TUs)>, <offset (in TUs)>
csa Send an 802.11h channel switch anouncement with chanspec:
<mode> <count> <channel>[a,b][n][u,l]
mode (0 or 1)
count (0-254)
channel number (0-224)
band a=5G, b=2G
bandwidth n=10, non for 20 & 40
ctl sideband, l=lower, u=upper, default no ctl sideband
constraint
Send an 802.11h Power Constraint IE
Usage: wl constraint 1-255 db
rm_req Request a radio measurement of type basic, cca, or rpi
specify a series of measurement types each followed by options.
example: wl rm_req cca -c 1 -d 50 cca -c 6 cca -c 11
Options:
-t n numeric token id for measurement set or measurement
-c n channel
-d n duration in TUs (1024 us)
-p parallel flag, measurement starts at the same time as previous
Each measurement specified uses the same channel and duration as the
previous unless a new channel or duration is specified.
rm_rep Get current radio measurement report
join_pref
Set/Get join target preferences.
assoc_pref
Set/Get association preference.
Usage: wl assoc_pref [auto|a|b|g]
wme Set WME (Wireless Multimedia Extensions) mode (0=off, 1=on, -1=auto)
wme_ac wl wme_ac ap|sta [be|bk|vi|vo [ecwmax|ecwmin|txop|aifsn|acm <value>] ...]
wme_apsd
Set APSD (Automatic Power Save Delivery) mode on AP (0=off, 1=on)
wme_apsd_sta
Set APSD parameters on STA. Driver must be down.
Usage: wl wme_apsd_sta <max_sp_len> <be> <bk> <vi> <vo>
<max_sp_len>: number of frames per USP: 0 (all), 2, 4, or 6
<xx>: value 0 to disable, 1 to enable U-APSD per AC
wme_dp Set AC queue discard policy.
Usage: wl wme_dp <be> <bk> <vi> <vo>
<xx>: value 0 for newest-first, 1 for oldest-first
wme_counters
print WMM stats
wme_clear_counters
clear WMM counters
wme_tx_params
wl wme_tx_params [be|bk|vi|vo [short|sfb|long|lfb|max_rate <value>] ...]
wme_maxbw_params
wl wme_maxbw_params [be|bk|vi|vo <value> ....]
lifetime
Set Lifetime parameter (milliseconds) for each ac.
wl lifetime be|bk|vi|vo [<value>]
reinit Reinitialize device
sta_info
wl sta_info <xx:xx:xx:xx:xx:xx>
cap driver capabilities
malloc_dump
Deprecated. Folded under 'wl dump malloc
chan_info
channel info
add_ie Add a vendor proprietary IE to 802.11 management packets
Usage: wl add_ie <pktflag> length OUI hexdata
<pktflag>: Bit 0 - Beacons
Bit 1 - Probe Rsp
Bit 2 - Assoc/Reassoc Rsp
Bit 3 - Auth Rsp
Bit 4 - Probe Req
Bit 5 - Assoc/Reassoc Req
Example: wl add_ie 3 10 00:90:4C 0101050c121a03
to add this IE to beacons and probe responses
del_ie Delete a vendor proprietary IE from 802.11 management packets
Usage: wl del_ie <pktflag> length OUI hexdata
<pktflag>: Bit 0 - Beacons
Bit 1 - Probe Rsp
Bit 2 - Assoc/Reassoc Rsp
Bit 3 - Auth Rsp
Bit 4 - Probe Req
Bit 5 - Assoc/Reassoc Req
Example: wl del_ie 3 10 00:90:4C 0101050c121a03
list_ie Dump the list of vendor proprietary IEs
rand Get a 2-byte Random Number from the MAC's PRNG
Usage: wl rand
otpw Write an srom image to on-chip otp
Usage: wl otpw file
nvotpw Write nvram to on-chip otp
Usage: wl nvotpw file
bcmerrorstr
errorstring
freqtrack
Set Frequency Tracking Mode (0=Auto, 1=On, 2=OFF)
eventing
set/get 128-bit hex filter bitmask for MAC event reporting up to application layer
event_msgs
set/get 128-bit hex filter bitmask for MAC event reporting via packet indications
counters
Return driver counter values
delta_stats_interval
set/get the delta statistics interval in seconds (0 to disable)
delta_stats
get the delta statistics for the last interval
assoc_info
Returns the assoc req and resp information [STA only]
autochannel
auto channel selection:
1 to issue a channel scanning;
2 to set chanspec based on the channel scan result;
without argument to only show the chanspec selected;
ssid must set to null before this process, RF must be up
csscantimer
auto channel scan timer in minutes (0 to disable)
closed hides the network from active scans, 0 or 1.
0 is open, 1 is hide
pmkid_info
Returns the pmkid table
abminrate
get/set afterburner minimum rate threshold
bss set/get BSS enabled status: up/down
closednet
set/get BSS closed network attribute
ap_isolate
set/get AP isolation
eap_restrict
set/get EAP restriction
diag diag testindex(1-interrupt, 2-loopback, 3-memory, 4-led); precede by 'wl down' and follow by 'wl up'
reset_d11cnts
reset 802.11 MIB counters
staname get/set station name:
Maximum name length is 15 bytes
apname get AP name
otpdump Dump raw otp
otpstat Dump OTP status
nrate -r legacy rate (CCK, OFDM)-m mcs index-s stf mode (0=SISO,1=CDD,2=STBC(not supported),3=SDM)-w Override mcs only to support STA's with/without STBC capability
mimo_txbw
get/set mimo txbw (2=20Mhz(lower), 3=20Mhz upper, 4=40Mhz, 5=40Mhz dup<mcs32 only)
cac_addts
add TSPEC, error if STA is not associated or WME is not enabled
arg: TSPEC parameter input list
cac_delts
delete TSPEC, error if STA is not associated or WME is not enabled
arg: TSINFO for the target tspec
cac_delts_ea
delete TSPEC, error if STA is not associated or WME is not enabled
arg1: Desired TSINFO for the target tspec
arg2: Desired MAC address
cac_tslist
Get the list of TSINFO in driver
eg. 'wl cac_tslist' get a list of TSINFO
cac_tslist_ea
Get the list of TSINFO for given STA in driver
eg. 'wl cac_tslist_ea ea' get a list of TSINFO
cac_tspec
Get specific TSPEC with matching TSINFO
eg. 'wl cac_tspec 0xaa 0xbb 0xcc' where 0xaa 0xbb & 0xcc are TSINFO octets
cac_tspec_ea
Get specific TSPEC for given STA with matching TSINFO
eg. 'wl cac_tspec 0xaa 0xbb 0xcc xx:xx:xx:xx:xx:xx'
where 0xaa 0xbb & 0xcc are TSINFO octets and xx is mac address
phy_txpwrindex
usage: (set) phy_txpwrindex core0_idx core1_idx core2_idx core3_idx (get) phy_txpwrindex, return format: core0_idx core1_idx core2_idx core3_idxSet/Get txpwrindex
phy_test_tssi
wl phy_test_tssi val
phy_test_tssi_offs
wl phy_test_tssi_offs val
phy_rssiant
wl phy_rssiant antindex(0-3)
phy_rssi_ant
Get RSSI per antenna (only gives RSSI of current antenna for SISO PHY)
lpphy_papdepstbl
print papd eps table; Usage: wl lpphy_papdepstbl
rifs set/get the rifs status; usage: wl rifs <1/0> (On/Off)
rifs_advert
set/get the rifs mode advertisement status; usage: wl rifs_advert <-1/0> (Auto/Off)
phy_rxiqest
Get phy RX IQ noise in dBm:
-s # of samples (2^n)
-a antenna select, 0,1 or 3
phy_txiqcc
usage: phy_txiqcc [a b]
Set/get the iqcc a, b values
phy_txlocc
usage: phy_txlocc [di dq ei eq fi fq]
Set/get locc di dq ei eq fi fq values
phytable
usage: wl phytable table_id offset width_of_table_element [table_element]
Set/get table element of a table with the given ID at the given offset
Note that table width supplied should be 8 or 16 or 32
table ID, table offset can not be negative
pavars Set/get temp PA parameters
usage: wl down
wl pavars pa2gw0a0=0x1 pa2gw1a0=0x2 pa2gw2a0=0x3 ...
wl pavars
wl up
override the PA parameters after driver attach(srom read), before diver up
These override values will be propogated to HW when driver goes up
PA parameters in one band range (2g, 5gl, 5g, 5gh) must all present if
one of them is specified in the command, otherwise it will be filled with 0
povars Set/get temp power offset
usage: wl down
wl povars cck2gpo=0x1 ofdm2gpo=0x2 mcs2gpo=0x3 ...
wl povars
wl up
override the power offset after driver attach(srom read), before diver up
These override values will be propogated to HW when driver goes up
power offsets in one band range (2g, 5gl, 5g, 5gh) must all present if
one of them is specified in the command, otherwise it will be filled with 0 cck(2g only), ofdm, and mcs(0-7) for NPHY are supported
fem Set temp fem2g/5g value
usage: wl fem (tssipos2g=0x1 extpagain2g=0x2 pdetrange2g=0x1 triso2g=0x1 antswctl2g=0)
(tssipos5g=0x1 extpagain5g=0x2 pdetrange5g=0x1 triso5g=0x1 antswctl5g=0)
antgain Set temp ag0/1 value
usage: wl antgain ag0=0x1 ag1=0x2
maxpower
Set temp maxp2g(5g)a0(a1) value
usage: wl maxpower maxp2ga0=0x1 maxp2ga1=0x2 maxp5ga0=0xff maxp5ga1=0xff
maxp5gla0=0x3 maxp5gla1=0x4 maxp5gha0=0x5 maxp5gha1=0x6
phy_antsel
get/set antenna configuration
set: -1(AUTO), 0xAB(fixed antenna selection)
where A and B is the antenna numbers used for RF chain 1 and 0 respectively
query: <utx>[AUTO] <urx>[AUTO] <dtx>[AUTO] <drx>[AUTO]
where utx = TX unicast antenna configuration
urx = RX unicast antenna configuration
dtx = TX default (non-unicast) antenna configuration
drx = RX default (non-unicast) antenna configuration
txcore Usage: wl txcore -k <CCK core mask> -o <OFDM core mask> -s <1..4> -c <core bitmap>
-k CCK core mask
-o OFDM core mask
-s # of space-time-streams
-c active core (bitmask) to be used when transmitting frames
txchain_pwr_offset
Usage: wl txchain_pwr_offset [qdBm offsets]
Get/Set the current offsets for each core in qdBm (quarter dBm)
sample_collect
Optional parameters HTPHY/(NPHY with NREV >= 7) are:
-f File name to dump the sample buffer (default "sample_collect.dat")
-t Trigger condition (default now)
now, good_fcs, bad_fcs, bad_plcp, crs, crs_glitch, crs_deassert
-b PreTrigger duration in us (default 10)
-a PostTrigger duration in us (default 10)
-m Sample collect mode (default 1)
HTPHY: 0=adc, 1..3=adc+rssi, 4=gpio
NPHY: 1=Dual-Core adc[9:2], 2=Core0 adc[9:0], 3=Core1 adc[9:0], gpio=gpio
-g GPIO mux select (default 0)
use only for gpio mode
-d Downsample enable (default 0)
use only for HTPHY
-e BeDeaf enable (default 0)
-i Timeout in units of 10us (default 1000)
Optional parameters (NPHY with NREV < 7) are:
-f File name to dump the sample buffer (binary format, default "sample_collect.dat")
-u Sample collect duration in us (default 60)
-c Cores to do sample collect, only if BW=40MHz (default both)
For (NREV < 7), the NPHY buffer returned has the format:
In 20MHz [(uint16)num_bytes, <I(core0), Q(core0), I(core1), Q(core1)>]
In 40MHz [(uint16)num_bytes(core0), <I(core0), Q(core0)>,
(uint16)num_bytes(core1), <I(core1), Q(core1)>]
txfifo_sz
set/get the txfifo size; usage: wl txfifo_sz <fifonum> <size_in_bytes>
rate_histo
Get rate hostrogram
pkteng_start
start packet engine tx usage: wl pkteng_start <xx:xx:xx:xx:xx:xx> <tx|txwithack> [(async)|sync] [ipg] [len] [nframes] [src]
start packet engine rx usage: wl pkteng_start <xx:xx:xx:xx:xx:xx> <rx|rxwithack> [(async)|sync] [rxframes] [rxtimeout]
sync: synchronous mode
ipg: inter packet gap in us
len: packet length
nframes: number of frames; 0 indicates continuous tx test
src: source mac address
rxframes: number of receive frames (sync mode only)
rxtimeout: maximum timout in msec (sync mode only)
pkteng_stop
stop packet engine; usage: wl pkteng_stop <tx|rx>
pkteng_stats
packet engine stats; usage: wl pkteng_stats
wowl Enable/disable WOWL events
0 - Clear all events
Bit 0 - Wakeup on Magic Packet
Bit 1 - Wakeup on NetPattern (use 'wl wowl_pattern' to configure pattern)
Bit 2 - Wakeup on loss-of-link due to Disassociation/Deauth
Bit 3 - Wakeup on retrograde tsf
Bit 4 - Wakeup on loss of beacon (use 'wl wowl_bcn_loss' to configure time)
wowl_bcn_loss
Set #of seconds of beacon loss for wakeup event
wowl_pattern
usage: wowl_pattern [ [clr | [[ add | del ] offset mask value ]]]
No options -- lists existing pattern list
add -- Adds the pattern to the list
del -- Removes a pattern from the list
clr -- Clear current list
offset -- Starting offset for the pattern
mask -- Mask to be used for pattern. Bit i of mask => byte i of the pattern
value -- Value of the pattern
wowl_wakeind
usage: wowl_wakeind [clear]
Shows last system wakeup event indications from PCI and D11 cores
clear - Clear the indications
wowl_status
usage: wowl_status [clear]
Shows last system wakeup setting
wowl_pkt
Send a wakeup frame to wakup a sleeping STA in WAKE mode
Usage: wl wowl_pkt <len> <dst ea | bcast | ucast <STA ea>>[ magic [<STA ea>] | net <offset> <pattern>]
e.g. To send bcast magic frame -- wl wowl_pkt 102 bcast magic 00:90:4c:AA:BB:CC
To send ucast magic frame -- wl wowl_pkt 102 ucast 00:90:4c:aa:bb:cc magic
To send a frame with L2 unicast - wl wowl_pkt 102 00:90:4c:aa:bb:cc net 0 0x00904caabbcc
NOTE: offset for netpattern frame starts from "Dest EA" of ethernet frame.So dest ea will be used only when offset is >= 6
wme_apsd_trigger
Set Periodic APSD Trigger Frame Timer timeout in ms (0=off)
wme_autotrigger
Enable/Disable sending of APSD Trigger frame when all ac are delivery enabled
reassoc Initiate a (re)association request.
Usage: wl reassoc <bssid> [options]
Options:
-c CL, --chanspecs=CL chanspecs (comma or space separated list)
send_nulldata
Sed a null frame to the specified hw address
btc_params
g/set BT Coex parameters
btc_flags
g/set BT Coex flags
obss_scan_params
set/get Overlapping BSS scan parameters
Usage: wl obss_scan a b c d e ...; where
a-Passive Dwell, {5-1000TU}, default = 100
b-Active Dwell, {10-1000TU}, default = 20
c-Width Trigger Scan Interval, {10-900sec}, default = 300
d-Passive Total per Channel, {200-10000TU}, default = 200
e-Active Total per Channel, {20-1000TU}, default = 20
f-Channel Transition Delay Factor, {5-100}, default = 5
g-Activity Threshold, {0-100%}, default = 25
keep_alive
Send specified "keep-alive" packet periodically.
Usage: wl keep_alive <period> <packet>
period: Re-transmission period in milli-seconds. 0 to disable packet transmits.
packet: Hex packet contents to transmit. The packet contents should include the entire ethernet packet (ethernet header, IP header, UDP header, and UDP payload) specified in network byte order.
e.g. Send keep alive packet every 30 seconds:
wl keep_alive 30000 0x0014a54b164f000f66f45b7e08004500001e000040004011c52a0a8830700a88302513c413c4000a00000a0d
srchmem g/set ucode srch engine memory
pkt_filter_add
Install a packet filter.
Usage: wl pkt_filter_add <id> <polarity> <type> <offset> <bitmask> <pattern>
id: Integer. User specified id.
type: 0 (Pattern matching filter).
offset: Integer. Offset within received packets to start matching.
polarity: Set to 1 to negate match result. 0 is default.
bitmask: Hex bitmask that indicates which bits of 'pattern' to match. Must be same
size as 'pattern'. Bit 0 of bitmask corresponds to bit 0 of pattern, etc.
If bit N of bitmask is 0, then do *not* match bit N of the pattern with
the received payload. If bit N of bitmask is 1, then perform match.
pattern: Hex pattern to match.
pkt_filter_clear_stats
Clear packet filter statistic counter values.
Usage: wl pkt_filter_clear_stats <id>
pkt_filter_enable
Enable/disable a packet filter.
Usage: wl pkt_filter_enable <id> <0|1>
pkt_filter_list
List installed packet filters.
Usage: wl pkt_filter_list [val]
val: 0 (disabled filters) 1 (enabled filters)
pkt_filter_mode
Set packet filter match action.
Usage: wl pkt_filter_mode <value>
value: 1 - Forward packet on match, discard on non-match (default).
0 - Discard packet on match, forward on non-match.
pkt_filter_delete
Uninstall a packet filter.
Usage: wl pkt_filter_delete <id>
pkt_filter_stats
Retrieve packet filter statistic counter values.
Usage: wl pkt_filter_stats <id>
seq_start
Initiates command batching sequence. Subsequent IOCTLs will be queued until
seq_stop is received.
seq_stop
Defines the end of command batching sequence. Queued IOCTLs will be executed.
seq_delay
Driver should spin for the indicated amount of time.
It is only valid within the context of batched commands.
seq_error_index
Used to retrieve the index (starting at 1) of the command that failed within a batch
bmac_reboot
Reboot BMAC
txmcsset
get Transmit MCS rateset for 11N device
rxmcsset
get Receive MCS rateset for 11N device
mimo_ss_stf
get/set SS STF mode.
Usage: wl mimo_ss_stf <value> <-b a | b>
value: 0 - SISO; 1 - CDD
-b(band): a - 5G; b - 2.4G
assoclistinfo
AP only: Get the list of yet another form of associated station info
scblist AP only: Get STA list
assertlog
get external assert logs
Usage: wl assertlog
assert_type
set/get the asset_bypass flag; usage: wl assert_type <1/0> (On/Off)
ledbh set/get led behavior
Usage: wl ledbh [0-3] [0-15]
obss_coex_action
send OBSS 20/40 Coexistence Mangement Action Frame
Usage: wl obss_coex_action -i <1/0> -w <1/0> -c <channel list>
-i: 40MHz intolerate bit; -w: 20MHz width Req bit;
-c: channel list, 1 - 14
At least one option must be provided
chanim_state
get channel interference state
Usage: wl chanim_state channel
Valid channels: 1 - 14
returns: 0 - Acceptable; 1 - Severe
chanim_mode
get/set channel interference measure (chanim) mode
Usage: wl chanim_mode <value>
value: 0 - disabled; 1 - detection only; 2 - detection and avoidance
ledbh set/get led behavior
Usage: wl ledbh [0-3] [0-15]
led_blink_sync
set/get led_blink_sync
Usage: wl led_blink_sync [0-3] [0/1]
cca_get_stats
Usage: wl cca_stats [-c channel] [-s num seconds][-a]
-c channel: Optional. specify channel. 0 = All channels. Default = current channel
-s num_seconds: Optional. Default = 10, Max = 60
-i: list individual measurements in addition to the averages
-curband: Only recommend channels on current band
itfr_get_stats
get interference source information
itfr_enab
get/set STA interference detection mode(STA only)
0 - disable
1 - enable maual detection
2 - enable auto detection
itfr_detect
issue an interference detection request
smfstats
get/clear selected management frame (smf) stats wl smfstats [-C num]|[--cfg=num] [auth]|[assoc]|[reassoc]|[clear]
clear - to clear the stats
manfinfo
show chip package info in OTP
rrm_nbr_req
send 11k neighbor report measurement request
Usage: wl 11k_nbr_req <da> [ssid]
pm_dur Retrieve accumulated PM duration information (GET) or clear accumulator (SET)
Usage: wl pm_dur <any-number-to-clear>
mpc_dur Retrieve accumulated MPC duration information in ms (GET) or clear accumulator (SET)
Usage: wl mpc_dur <any-number-to-clear>
chanim_acs_record
get the auto channel scan record.
Usage: wl acs_record
dngl_wd enable or disable dongle watchdog timer
Usage: wl dngl_wd <on/off>(to turn on\off) <exptime in sec>
tsf set/get tsf register
Usage: wl tsf [<high> <low>]
tpc_mode
Enable/disable AP TPC.
Usage: wl tpc_mode <mode>
0 - disable, 1 - BSS power control, 2 - AP power control, 3 - Both (1) and (2)
tpc_period
Set AP TPC periodicity in secs.
Usage: wl tpc_period <secs>
tpc_lm Get current link margins.
mfp_sa_query
Send a sa query req/resp to a peer
usage: wl mfp_sa_query <Dest Mac Addr> action id flag
mfp_disassoc
send bogus disassoc
Usage: wl mfp_disassoc
mfp_deauth
send bogus deauth
Usage: wl mfp_dedauth
mfp_assoc
send assoc
Usage: wl mfp_assoc
mfp_auth
send auth
Usage: wl mfp_auth
mfp_reassoc
send reassoc
Usage: wl mfp_reassoc
monitor_lq
Start/Stop monitoring link quality metrics - RSSI and SNR
Usage: wl monitor_lq <0: turn off / 1: turn on
monitor_lq_status
Returns averaged link quality metrics - RSSI and SNR values
scb_probe
Set probing parameters for inactive clients.
<timout in seconds> <activity_time in seconds> <max number of probes>
rpmt rpmt <pm1-to> <pm0-to>
spatial_policy
set/get spatial_policy
Usage: wl spatial_policy <-1: auto / 0: turn off / 1: turn on>
to control individual band/sub-band use
wl spatial_policy a b c d e
where a is 2.4G band setting
where b is 5G lower band setting
where c is 5G middle band setting
where d is 5G high band setting
where e is 5G upper band setting
>
Hi. Please help. What command should I reconnect to the Internet?
ReplyDeleteWhat is the command for changing password in cli
ReplyDeleteHello!
DeleteThat would be the "passwd" command to change the password for Telnet.
Regards,
Ahmed